[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"detail-sidebar-cat-0-en-105":3,"doc-seo-561645-105":59,"doc-detail-561645-en":131},{"code":4,"msg":5,"data":6},0,"success",[7,13,18,23,28,33,38,43,48,51,55],{"id":8,"doc_module":4,"doc_module_name":9,"category_name":10,"show_sort_weight":11,"slug":12},1,"Document","Story & Novel",90,"story-novel",{"id":14,"doc_module":4,"doc_module_name":9,"category_name":15,"show_sort_weight":16,"slug":17},2,"Literature",80,"literature",{"id":19,"doc_module":4,"doc_module_name":9,"category_name":20,"show_sort_weight":21,"slug":22},4,"Exam",70,"exam",{"id":24,"doc_module":4,"doc_module_name":9,"category_name":25,"show_sort_weight":26,"slug":27},5,"Comic",60,"comic",{"id":29,"doc_module":4,"doc_module_name":9,"category_name":30,"show_sort_weight":31,"slug":32},6,"Technology",50,"technology",{"id":34,"doc_module":4,"doc_module_name":9,"category_name":35,"show_sort_weight":36,"slug":37},7,"Healthcare",40,"healthcare",{"id":39,"doc_module":4,"doc_module_name":9,"category_name":40,"show_sort_weight":41,"slug":42},8,"Research & Report",30,"research-report",{"id":44,"doc_module":4,"doc_module_name":9,"category_name":45,"show_sort_weight":46,"slug":47},9,"Religion & Spirituality",20,"religion-spirituality",{"id":46,"doc_module":4,"doc_module_name":9,"category_name":49,"show_sort_weight":46,"slug":50},"World Cup","world-cup",{"id":52,"doc_module":4,"doc_module_name":9,"category_name":53,"show_sort_weight":52,"slug":54},10,"Lifestyle","lifestyle",{"id":56,"doc_module":4,"doc_module_name":9,"category_name":57,"show_sort_weight":24,"slug":58},19,"General","general",{"code":4,"msg":60,"data":61},"ok",{"site_id":62,"language":63,"slug":64,"title":65,"keywords":66,"description":67,"schema_data":68,"social_meta":124,"head_meta":126,"extra_data":128,"updated_unix":130},105,"en","linkswitch-tn-design-guide-application-note-an-37-quick-start-guide","LinkSwitch-TN - Design Guide - Application Note AN-37 - Quick Start Guide","","LinkSwitch-TN combines a high-voltage power MOSFET and an ON/OFF controller in a self-powered, fully fault-protected device with jittered switching for low EMI and auto-restart protection for overload and short-circuit events. High thermal shutdown with large hysteresis supports applications with elevated ambient temperature. The guide targets non-isolated power-supply designs using the LinkSwitch-TN family, presenting buck and buck-boost design procedures, complete component selection equations, and a quick-start flow to choose topology, device parameters, diodes, and output capacitors for efficient, low-cost operation.",{"@graph":69,"@context":123},[70,84,106],{"@type":71,"itemListElement":72},"BreadcrumbList",[73,77,79,82],{"item":74,"name":75,"@type":76,"position":8},"https://docshare.wps.com","Home","ListItem",{"item":78,"name":9,"@type":76,"position":14},"https://docshare.wps.com/document/",{"item":80,"name":40,"@type":76,"position":81},"https://docshare.wps.com/document/research-report/",3,{"item":83,"name":65,"@type":76,"position":19},"https://docshare.wps.com/document/linkswitch-tn-design-guide-application-note-an-37-quick-start-guide/561645/",{"url":83,"name":65,"@type":85,"image":86,"author":91,"headline":65,"publisher":94,"fileFormat":97,"inLanguage":63,"description":67,"dateModified":98,"datePublished":99,"encodingFormat":97,"isAccessibleForFree":100,"interactionStatistic":101},"DigitalDocument",{"url":87,"@type":88,"width":89,"height":90},"https://docshare.wps.com/thumbnails/linkswitch-tn-design-guide-application-note-an-37-quick-start-guide/561645.png","ImageObject",300,407,{"name":92,"@type":93},"Kurz","Person",{"url":74,"name":95,"@type":96},"DocShare","Organization","application/pdf","2026-11-19","2026-10-12",true,{"@type":102,"interactionType":103,"userInteractionCount":105},"InteractionCounter",{"@type":104},"ViewAction",11,{"@type":107,"mainEntity":108},"FAQPage",[109,115,119],{"name":110,"@type":111,"acceptedAnswer":112},"What protections does LinkSwitch-TN provide during overload, short circuit, and thermal faults?","Question",{"text":113,"@type":114},"It uses auto-restart to limit dissipation during overload and output short circuit, and over-temperature protection disables the internal MOSFET during thermal faults.","Answer",{"name":116,"@type":111,"acceptedAnswer":117},"Which applications are LinkSwitch-TN intended for in non-isolated designs?",{"text":118,"@type":114},"It is designed for non-isolated supplies such as appliances, nightlights, emergency exit signs, and LED drivers, with configurations that support line/neutral referenced outputs.",{"name":120,"@type":111,"acceptedAnswer":121},"How do engineers begin a quick design using the AN-37 quick start section?",{"text":122,"@type":114},"They select the input stage, choose the topology, pick the LinkSwitch-TN device and related components based on the tables, select the freewheeling diode to meet reverse recovery needs, set output capacitance, and then prototype and verify.","https://schema.org",{"og:url":83,"og:type":125,"og:title":65,"og:site_name":95,"og:description":67},"article",{"robots":127,"canonical":83},"index,follow",{"doc_id":129,"site_id":62},561645,1791886745,{"code":4,"msg":5,"data":132},{"doc_id":129,"user_id":133,"nickname":92,"user_avatar":134,"doc_module":4,"category_id":39,"category_name":40,"doc_title":65,"doc_description":67,"doc_content":135,"file_id":136,"file_url":137,"file_type":138,"file_size":139,"view_count":105,"is_deleted":4,"is_public":8,"is_downloadable":8,"audit_status":8,"page_count":140,"language":141,"language_code":63,"site_id":62,"html_lang":63,"table_of_contents":142,"faqs":143,"seo_title":144,"seo_description":67,"update_tm":145,"read_time":36,"preview_page_count":19,"preview_urls":146},2336478945635,"https://ap-avatar.wpscdn.com/davatar_6f874abed73319feea01a86fa6f0fab8","LinkSwitch®-TN  \nDesign Guide  \nApplication Note AN-37  \nIntroduction  \nLinkSwitch-TN combines a high voltage power MOSFET switch with an ON/OFF controller in one device. It is completely selfpowered from the DRAIN pin, has ajittered switching frequency for low EMI and is fully fault protected. Auto-restart limits device and circuit dissipation during overload and output short circuit (LNK304-306) while over temperature protection disables the internal MOSFET during thermal faults. The high thermal shutdown threshold is ideal for applications where the ambient temperature is high while the large hysteresis protects the PCB and surrounding components from high average temperatures.  \nLinkSwitch-TN is designed for any application where a nonisolated supply is required such as appliances (coffee machines, rice cookers, dishwashers, microwave ovens etc.), nightlights, emergency exit signs and LED drivers. LinkSwitch-TN can be configured in all common topologies to give a line or neutral referenced output and an inverted or non-inverted output voltage–ideal for applications using triacs for AC load control. Using a switching power supply rather than a passive dropper (capacitive or resistive) gives a number of advantages, some of which are listed below.  \n• Universal input – the same power supply/product can be used worldwide  \n• High power density – smaller size, no µF’s of X class capacitance needed  \n• High efficiency – full load efficiencies >75% typical for  \n12 V output  \n• Excellent line and load regulation  \n• High efficiency at light load – ON/OFF control maintains high efficiency even at light load  \n• Extremely energy efficient – input power \u003C100 mW at no load  \n• Entirely manufacturable in SMD  \n• More robust to drop test mechanical shock  \n• Fully fault protected (overload, short circuit and thermal faults)  \n• Scalable – LinkSwitch-TN family allows the same basic design to be used from \u003C50 mA to 360 mA  \nScope  \nThis application note is for engineers designing a non-isolated power supply using the LinkSwitch-TN family of devices. This document describes the design procedure for buck and buck-  \nRFB DFB  \nVO  \nRF  \nDIN2  \nLIN  \nCIN1  \nAC Input  \n1 (a)  \nPI-3764-121003  \nRFB  \nDFB  \nVO  \nAC Input  \nRF  \nDIN1  \nLIN  \n1 (b)  \nPI-3765-121003  \nFigure 1 (a) . Basic Configuration using LinkSwitch-TN in a Buck Converter. Figure 1 (b) Basic Configuration using LinkSwitch-TN in a Buck-Boost Converter.  \nAN-37  \nboost converters using the LinkSwitch-TN family of integrated off-line switchers. The objective of this document is to provide power supply engineers with guidelines in order to enable them to quickly build efficient and low cost buck or buck-boost converter based power supplies using low cost off-the-shelf inductors. Complete design equations are provided for the selection of the converter’s key components. Since the power MOSFET and controller are integrated into a single IC the design process is greatly simplified, the circuit configuration has few parts and no transformeris required. Therefore a quick start section is provided that allows off-the-shelf components tobe selected for common output voltages and currents.  \nIn addition to this application note a design spreadsheet is available within the PIXls tool inthePI Expert design software suite. The reader may also find the LinkSwitch-TN DAK engineering prototype board useful as an example of a working supply. Further details of support tools and updates to this [document can be found at](document can be found at www.powerint.com)[ www.powerint.com](document can be found at www.powerint.com).  \nQuick Start  \nReaders wanting to start immediately can use the following information to quickly select the components for a new design, using Figure 1 and Tables 1 and 2 as references.  \n1) For AC input designs select the input stage (Table 9) .  \n2) Select the topology (Tables 1 and 2) .  \n- If better than ±10% output regulation is required, then use optocoupler feedback wi","cbCaibQVtoblvWn8","https://ap.wps.com/l/cbCaibQVtoblvWn8","pdf",334864,16,"English","# Introduction\n# Scope\n# Quick Start\n## Component Selection Steps\n# Table 1. LinkSwitch-TN Circuit Configurations Using Directly Sensed Feedback\n# Table 1 (continued) and Key Features","[{\"question\":\"What protections does LinkSwitch-TN provide during overload, short circuit, and thermal faults?\",\"answer\":\"It uses auto-restart to limit dissipation during overload and output short circuit, and over-temperature protection disables the internal MOSFET during thermal faults.\"},{\"question\":\"Which applications are LinkSwitch-TN intended for in non-isolated designs?\",\"answer\":\"It is designed for non-isolated supplies such as appliances, nightlights, emergency exit signs, and LED drivers, with configurations that support line/neutral referenced outputs.\"},{\"question\":\"How do engineers begin a quick design using the AN-37 quick start section?\",\"answer\":\"They select the input stage, choose the topology, pick the LinkSwitch-TN device and related components based on the tables, select the freewheeling diode to meet reverse recovery needs, set output capacitance, and then prototype and verify.\"}]","LinkSwitch-TN - Design Guide - Application Note AN-37 - Quick Start Guide | PDF",1791806463,[147,151,155,159],{"page_no":8,"url":148,"width":149,"height":150},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/62f388772d51dbebc994e23f1b4b16d6.webp",983,1272,{"page_no":14,"url":152,"width":153,"height":154},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/3403b2c502272a583ca8ab7d161c1475.webp",982,1270,{"page_no":81,"url":156,"width":157,"height":158},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/2c2e4787f4f18c5015a5810ae77c2490.webp",981,1269,{"page_no":19,"url":160,"width":161,"height":162},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/d5a88da87eedd5cbada20211daa7087a.webp",980,1268]