[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"detail-sidebar-cat-0-en-105":3,"doc-seo-676538-105":59,"doc-detail-676538-en":133},{"code":4,"msg":5,"data":6},0,"success",[7,13,18,23,28,33,38,43,48,51,55],{"id":8,"doc_module":4,"doc_module_name":9,"category_name":10,"show_sort_weight":11,"slug":12},1,"Document","Story & Novel",90,"story-novel",{"id":14,"doc_module":4,"doc_module_name":9,"category_name":15,"show_sort_weight":16,"slug":17},2,"Literature",80,"literature",{"id":19,"doc_module":4,"doc_module_name":9,"category_name":20,"show_sort_weight":21,"slug":22},4,"Exam",70,"exam",{"id":24,"doc_module":4,"doc_module_name":9,"category_name":25,"show_sort_weight":26,"slug":27},5,"Comic",60,"comic",{"id":29,"doc_module":4,"doc_module_name":9,"category_name":30,"show_sort_weight":31,"slug":32},6,"Technology",50,"technology",{"id":34,"doc_module":4,"doc_module_name":9,"category_name":35,"show_sort_weight":36,"slug":37},7,"Healthcare",40,"healthcare",{"id":39,"doc_module":4,"doc_module_name":9,"category_name":40,"show_sort_weight":41,"slug":42},8,"Research & Report",30,"research-report",{"id":44,"doc_module":4,"doc_module_name":9,"category_name":45,"show_sort_weight":46,"slug":47},9,"Religion & Spirituality",20,"religion-spirituality",{"id":46,"doc_module":4,"doc_module_name":9,"category_name":49,"show_sort_weight":46,"slug":50},"World Cup","world-cup",{"id":52,"doc_module":4,"doc_module_name":9,"category_name":53,"show_sort_weight":52,"slug":54},10,"Lifestyle","lifestyle",{"id":56,"doc_module":4,"doc_module_name":9,"category_name":57,"show_sort_weight":24,"slug":58},19,"General","general",{"code":4,"msg":60,"data":61},"ok",{"site_id":62,"language":63,"slug":64,"title":65,"keywords":66,"description":67,"schema_data":68,"social_meta":126,"head_meta":128,"extra_data":130,"updated_unix":132},105,"en","lemon-rx-microbrick-basic-manual","Lemon RX Microbrick - Basic Manual","","The Lemon RX Microbrick Basic Manual explains the Microbrick receiver’s capabilities and how to connect it for operation. It describes five flight control channels in a standard Spektrum-compatible order, plus internal stabilization-related channels, and details available circuit-board solder pads and connector options. Power guidance covers brushed 1s setups using the onboard 5A brushed ESC and brushless 2s setups with an external ESC, including polarity warning and low-voltage behavior. It also outlines failsafe operation and provides an overview of optional three-axis stabilization, including how to configure unstabilized versus stabilization-enabled use.",{"@graph":69,"@context":125},[70,84,104],{"@type":71,"itemListElement":72},"BreadcrumbList",[73,77,79,82],{"item":74,"name":75,"@type":76,"position":8},"https://docshare.wps.com","Home","ListItem",{"item":78,"name":9,"@type":76,"position":14},"https://docshare.wps.com/document/",{"item":80,"name":30,"@type":76,"position":81},"https://docshare.wps.com/document/technology/",3,{"item":83,"name":65,"@type":76,"position":19},"https://docshare.wps.com/document/lemon-rx-microbrick-basic-manual/676538/",{"url":83,"name":65,"@type":85,"image":86,"author":91,"headline":65,"publisher":94,"fileFormat":97,"inLanguage":63,"description":67,"dateModified":98,"datePublished":98,"encodingFormat":97,"isAccessibleForFree":99,"interactionStatistic":100},"DigitalDocument",{"url":87,"@type":88,"width":89,"height":90},"https://docshare.wps.com/thumbnails/lemon-rx-microbrick-basic-manual/676538.png","ImageObject",300,407,{"name":92,"@type":93},"jay","Person",{"url":74,"name":95,"@type":96},"DocShare","Organization","application/pdf","2026-11-04",true,{"@type":101,"interactionType":102,"userInteractionCount":4},"InteractionCounter",{"@type":103},"ViewAction",{"@type":105,"mainEntity":106},"FAQPage",[107,113,117,121],{"name":108,"@type":109,"acceptedAnswer":110},"What transmitter type is recommended for full access to the Microbrick’s features?","Question",{"text":111,"@type":112},"A modern programmable DSMX/DSM2-compatible transmitter is recommended, such as Spektrum Generation 2 transmitters (e.g., DX6e, DX8G2, iX12). The manual also points users to a reference guide for advice with other compatible equipment.","Answer",{"name":114,"@type":109,"acceptedAnswer":115},"How should the Microbrick be powered for a brushed versus a brushless setup?",{"text":116,"@type":112},"For a brushed motor, connect a single LiPo cell (1s) to Ground (V-) and V+; the motor is powered through the built-in 5A brushed ESC. For a brushless motor, connect an external ESC to Ground (V-), V+, and Throttle Out, typically powered by a 2s battery with the ESC BEC providing 5.0v to the receiver and servos.",{"name":118,"@type":109,"acceptedAnswer":119},"What happens when the signal is lost (failsafe behavior)?",{"text":120,"@type":112},"When signal is lost, control pulses stop and servos normally remain at their last commanded position. After a brief delay, the motor stops; with the onboard brushed controller this is built in, and with an external brushless ESC the ESC should cut motor power (users should test small ESCs).",{"name":122,"@type":109,"acceptedAnswer":123},"How does stabilization configuration differ between Setup 1 and Setup 2?",{"text":124,"@type":112},"The manual first covers use as a simple unstabilized system in Setup 1: Unstabilized, where stabilization is not used. Setup 2: Stabilization Enabled contains the details for enabling the optional three-axis rate stabilization (similar to AS3X) to smooth flight in turbulent air.","https://schema.org",{"og:url":83,"og:type":127,"og:title":65,"og:site_name":95,"og:description":67},"article",{"robots":129,"canonical":83},"index,follow",{"doc_id":131,"site_id":62},676538,1793776023,{"code":4,"msg":5,"data":134},{"doc_id":131,"user_id":135,"nickname":92,"user_avatar":136,"doc_module":4,"category_id":29,"category_name":30,"doc_title":65,"doc_description":67,"doc_content":137,"file_id":138,"file_url":139,"file_type":140,"file_size":141,"view_count":4,"is_deleted":4,"is_public":8,"is_downloadable":8,"audit_status":8,"page_count":39,"language":142,"language_code":63,"site_id":62,"html_lang":63,"table_of_contents":143,"faqs":144,"seo_title":145,"seo_description":67,"update_tm":132,"read_time":46},3985747858866,"https://ap-avatar.wpscdn.com/davatar_a8503ba1806abce46bf441b54a3ca4cd","Lemon RX Microbrick: Basic Manual  \nIntroduction  \nThe Lemon Microbrick combines a full-range DSMX™/DSM2™ compatible receiver with two onboard ultramicro servos and a 5A brushed speed controller in a package that weighs under 7g. It has connectors for two external servos and can also support a separate brushless ESC. Finally, it provides optional three-axis stabilization (similar to AS3X™) . It is an ideal solution for models up to about 250g, including many lightweight UMX type planes.  \nThis Basic Manual, prepared by two enthusiastic users of Lemon equipment, jj604 and Daedalus66, is intended to provide the essential information about the Microbrick. It expands upon the instruction sheet provided by Lemon RX (which readers should also consult) . Our separate Reference Guide provides additional information likely to be of assistance to some users.  \nThe Microbrick can be used with almost any DSMX™/DSM2™ compatible transmitter, but for fullest access to its features, a modern programmable transmitter is desirable. This manual assumes that a Spektrum Generation 2 transmitter, such as the DX6e, DX6, DX8G2, DX8e, DX9, NX6, NX8, iX12, [etc. is](etc. is) used. Advice on use with other equipment, such as DX6i, DX8G1, RadioMaster TX16s or an OpenTX/ErSkyTX transmitter fitted with a DSMX™/DSM2™ compatible module are provided in the Reference Guide.  \nLemon Microbrick Overall Layout (connector type may vary)  \nMicrobrick Basic Manual v1 .0.29.docx  \nLemon RX Microbrick: Basic Manual  \nMain Features  \nChannels  \nThe Microbrick has five available flight control channels in the usual Spektrum order, plus two internal stabilization control channels:  \nChannel 1: Throttle (onboard 5A brushed throttle or external signal for a brushless ESC)  \nChannel 2: Aileron (RAL in dual setups); OR Rudder in Rudder Steering mode  \nChannel 3: Elevator onboard servo  \nChannel 4: Rudder onboard servo (channel not used in Rudder Steering mode)  \nChannel 5: On/Off control of stabilizer (internal only)  \nChannel 6: Aux1 (LAL in dual servo aileron setups)  \nChannel 7: Not available  \nChannel 8: Master gain control of stabilizer sensitivity (internal only)  \nConnections  \nAs shown in the photo on page 1, five solder pads are available on the circuit board. These provide ground (V-), positive power in (V+), throttle signal out for a brushless ESC, and two pads to power a brushed motor from the internal ESC. Wires can be soldered directly to the pads or header pins may be soldered in place to accept a regular servo connector.  \nThe Microbrick is available in several configurations which differ only in the connection arrangements. Depending on the configuration ordered, there may be a power connector cable soldered to ground and V+ . On some versions a small 3 pin connector is soldered to the two brushed motor pads (see photo on page 4) . The leftmost pin (1) is connected to Motor+, the other two (2, 3) to Motor̶- . An E-Flite UMX motor connector can be plugged directly into 1 and 2.  \nPower  \nPower input to the Microbrick is most commonly provided in one of two ways:  \n1. For a brushed motor, a single LiPo cell (1s) is connected to Ground (V-) and V+ . This powers the receiver and servos. The motor is powered through the built-in 5A brushed ESC.  \n2. For a brushless motor, an external ESC is connected to Ground (V-), V+ and Throttle Out. It is most commonly fed by a two cell (2s) battery and its BEC (battery eliminator circuit) provides 5.0v to the receiver and servos.  \nWarning: Since neither the Microbrick nor an external ESC has reverse voltage protection, it is vital to ensure correct supply polarity.  \nOther possible power configurations and voltages are discussed in the Reference Guide.  \nExternal Servo Connections  \nChannels 2 (Ail) and 6 (Aux1) servo outputs are available on the two JST-SH 1.00mm 3 pin connectors.1 In a dual aileron servo setup, both channels are used, while in a single aileron servo (or dual servos with Y-cable) setup, channel 6 is availa","cbCaieof9Y4TDpEz","https://ap.wps.com/l/cbCaieof9Y4TDpEz","pdf",2032890,"English","# Introduction\n# Main Features\n## Channels\n## Connections\n## Power\n## External Servo Connections\n## Failsafe\n## Low Voltage Warning\n## Stabilization\n## Mounting the Microbrick","[{\"question\":\"What transmitter type is recommended for full access to the Microbrick’s features?\",\"answer\":\"A modern programmable DSMX/DSM2-compatible transmitter is recommended, such as Spektrum Generation 2 transmitters (e.g., DX6e, DX8G2, iX12). The manual also points users to a reference guide for advice with other compatible equipment.\"},{\"question\":\"How should the Microbrick be powered for a brushed versus a brushless setup?\",\"answer\":\"For a brushed motor, connect a single LiPo cell (1s) to Ground (V-) and V+; the motor is powered through the built-in 5A brushed ESC. For a brushless motor, connect an external ESC to Ground (V-), V+, and Throttle Out, typically powered by a 2s battery with the ESC BEC providing 5.0v to the receiver and servos.\"},{\"question\":\"What happens when the signal is lost (failsafe behavior)?\",\"answer\":\"When signal is lost, control pulses stop and servos normally remain at their last commanded position. After a brief delay, the motor stops; with the onboard brushed controller this is built in, and with an external brushless ESC the ESC should cut motor power (users should test small ESCs).\"},{\"question\":\"How does stabilization configuration differ between Setup 1 and Setup 2?\",\"answer\":\"The manual first covers use as a simple unstabilized system in Setup 1: Unstabilized, where stabilization is not used. Setup 2: Stabilization Enabled contains the details for enabling the optional three-axis rate stabilization (similar to AS3X) to smooth flight in turbulent air.\"}]","Lemon RX Microbrick - Basic Manual | PDF"]