[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"detail-sidebar-cat-0-en-105":3,"doc-seo-462515-105":59,"doc-detail-462515-en":130},{"code":4,"msg":5,"data":6},0,"success",[7,13,18,23,28,33,38,43,48,51,55],{"id":8,"doc_module":4,"doc_module_name":9,"category_name":10,"show_sort_weight":11,"slug":12},1,"Document","Story & Novel",90,"story-novel",{"id":14,"doc_module":4,"doc_module_name":9,"category_name":15,"show_sort_weight":16,"slug":17},2,"Literature",80,"literature",{"id":19,"doc_module":4,"doc_module_name":9,"category_name":20,"show_sort_weight":21,"slug":22},4,"Exam",70,"exam",{"id":24,"doc_module":4,"doc_module_name":9,"category_name":25,"show_sort_weight":26,"slug":27},5,"Comic",60,"comic",{"id":29,"doc_module":4,"doc_module_name":9,"category_name":30,"show_sort_weight":31,"slug":32},6,"Technology",50,"technology",{"id":34,"doc_module":4,"doc_module_name":9,"category_name":35,"show_sort_weight":36,"slug":37},7,"Healthcare",40,"healthcare",{"id":39,"doc_module":4,"doc_module_name":9,"category_name":40,"show_sort_weight":41,"slug":42},8,"Research & Report",30,"research-report",{"id":44,"doc_module":4,"doc_module_name":9,"category_name":45,"show_sort_weight":46,"slug":47},9,"Religion & Spirituality",20,"religion-spirituality",{"id":46,"doc_module":4,"doc_module_name":9,"category_name":49,"show_sort_weight":46,"slug":50},"World Cup","world-cup",{"id":52,"doc_module":4,"doc_module_name":9,"category_name":53,"show_sort_weight":52,"slug":54},10,"Lifestyle","lifestyle",{"id":56,"doc_module":4,"doc_module_name":9,"category_name":57,"show_sort_weight":24,"slug":58},19,"General","general",{"code":4,"msg":60,"data":61},"ok",{"site_id":62,"language":63,"slug":64,"title":65,"keywords":66,"description":67,"schema_data":68,"social_meta":123,"head_meta":125,"extra_data":127,"updated_unix":129},105,"en","hot-deformation-behavior-of-7085-aluminum-alloy-based-on-constitutive-model-processing-map-and-microstructure-evolution","Hot Deformation Behavior of 7085 Aluminum Alloy Based on Constitutive Model, Processing Map, and Microstructure Evolution","","To understand the hot deformation behavior of 7085 aluminum alloy, compression tests were performed under varied conditions (593–743 K/0.001–1 s−1). True stress–strain curves primarily exhibit dynamic recovery, but softening shifts toward dynamic recrystallization at higher temperatures and lower strain rates. The proposed strain-compensated Zener–Hollomon constitutive model forecasts flow stress with high accuracy (R2 = 0.992). Instability regions concentrate in high-strain-rate conditions, and optimal processing occurs at 693–743 K/0.01–0.001 s−1. Softening transitions from recovery-dominated to coordinated recovery plus recrystallization as temperature increases and strain rate decreases.",{"@graph":69,"@context":122},[70,84,105],{"@type":71,"itemListElement":72},"BreadcrumbList",[73,77,79,82],{"item":74,"name":75,"@type":76,"position":8},"https://docshare.wps.com","Home","ListItem",{"item":78,"name":9,"@type":76,"position":14},"https://docshare.wps.com/document/",{"item":80,"name":40,"@type":76,"position":81},"https://docshare.wps.com/document/research-report/",3,{"item":83,"name":65,"@type":76,"position":19},"https://docshare.wps.com/document/hot-deformation-behavior-of-7085-aluminum-alloy-based-on-constitutive-model-processing-map-and-microstructure-evolution/462515/",{"url":83,"name":65,"@type":85,"image":86,"author":91,"headline":65,"publisher":94,"fileFormat":97,"inLanguage":63,"description":67,"dateModified":98,"datePublished":99,"encodingFormat":97,"isAccessibleForFree":100,"interactionStatistic":101},"DigitalDocument",{"url":87,"@type":88,"width":89,"height":90},"https://docshare.wps.com/thumbnails/hot-deformation-behavior-of-7085-aluminum-alloy-based-on-constitutive-model-processing-map-and-microstructure-evolution/462515.png","ImageObject",300,407,{"name":92,"@type":93},"Putri","Person",{"url":74,"name":95,"@type":96},"DocShare","Organization","application/pdf","2026-11-10","2026-09-30",true,{"@type":102,"interactionType":103,"userInteractionCount":44},"InteractionCounter",{"@type":104},"ViewAction",{"@type":106,"mainEntity":107},"FAQPage",[108,114,118],{"name":109,"@type":110,"acceptedAnswer":111},"How were the hot deformation experiments for 7085 aluminum alloy performed?","Question",{"text":112,"@type":113},"Compression tests were carried out across temperatures of 593–743 K and strain rates of 0.001–1 s−1, covering varied thermomechanical conditions.","Answer",{"name":115,"@type":110,"acceptedAnswer":116},"What softening mechanisms dominate under different deformation conditions?",{"text":117,"@type":113},"The true stress–strain response mainly shows dynamic recovery, while higher temperatures combined with lower strain rates shift the dominant softening mechanism toward dynamic recrystallization.",{"name":119,"@type":110,"acceptedAnswer":120},"How is the flow stress predicted in this work and how accurate is it?",{"text":121,"@type":113},"A strain-compensated Zener–Hollomon constitutive model is constructed to forecast flow stress, achieving an R2 value of 0.992, indicating exceptional precision.","https://schema.org",{"og:url":83,"og:type":124,"og:title":65,"og:site_name":95,"og:description":67},"article",{"robots":126,"canonical":83},"index,follow",{"doc_id":128,"site_id":62},462515,1790812593,{"code":4,"msg":5,"data":131},{"doc_id":128,"user_id":132,"nickname":92,"user_avatar":133,"doc_module":4,"category_id":39,"category_name":40,"doc_title":65,"doc_description":67,"doc_content":134,"file_id":135,"file_url":136,"file_type":137,"file_size":138,"view_count":44,"is_deleted":4,"is_public":8,"is_downloadable":8,"audit_status":8,"page_count":139,"language":140,"language_code":63,"site_id":62,"html_lang":63,"table_of_contents":141,"faqs":142,"seo_title":143,"seo_description":67,"update_tm":144,"read_time":145,"preview_page_count":19,"preview_urls":146},962085571259,"https://ap-avatar.wpscdn.com/davatar_29158cc5080c5b710cf443261637dec0","Article  \nHot Deformation Behavior of 7085 Aluminum Alloy Based on Constitutive Model, Processing Map, and  \nMicrostructure Evolution  \nWenke Wang 1, Wenqing Li 1, Xiaolong Tang 2, Yuehua Sun 2 and Jian Ren 2, *  \nAcademic Editor: RadimKocich  \nReceived: 25 September 2025  \nRevised: 17 December 2025  \nAccepted: 23 December 2025  \nPublished: 26 December 2025  \nCopyright: © 2025 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license.  \n1 HIT (Weihai) Innovation Park Corporation Limited, Weihai 264209, China; [15b309020@hit.edu.cn](15b309020@hit.edu.cn) (W.W.); [liwenqing_2020@163.com](liwenqing_2020@163.com) (W.L.)  \n2 School of Materials Science and Engineering, Anhui University of Technology, Maanshan 243002, China; [txl000206@163.com](txl000206@163.com) (X.T.); [sunyuehua1008@126.com](sunyuehua1008@126.com) (Y.S.)  \n* Correspondence: [renjianahut@126.com](renjianahut@126.com)  \nAbstract  \nTo understand the hot deformation behavior of 7085 aluminum alloy, compression tests were performed under varied conditions (593–743 K/0.001–1 s−1) . While the true stress– strain curves predominantly display the features of dynamic recovery, the softening mechanism shifts towards dynamic recrystallization when deforming at higher temperatures and lower strain rates. The validity of the constructed strain-compensated Zener–Hollomon model is confirmed by its exceptional precision in forecasting the flow stress, achieving an R2 value of 0.992 . The instability areas are concentrated in the highstrain-rate regions, and the optimal deformation processing for 7085 aluminum alloy is 693–743 K/0.01–0.001 s−1 . The alloy’s softening mechanism undergoes a transition from solely dynamic recovery to a progressively more significant coordinated role of dynamic recovery and dynamic recrystallization as the temperature rises and the strain rate drops.  \nKeywords: 7085 aluminum alloy; hot compression; processing map; constitutive model  \n1. Introduction  \nThe status of 7085 aluminum alloy as a key aerospace material for large-scale integrated components (e.g., wrought ring products and aircraft frames) stems from its exceptional property profile. As an ultra-high strength alloy from the Al-Zn-Mg-Cu family, it offers an optimal balance of high specific strength, excellent hardenability, and good stress corrosion resistance [1–3] . However, this alloy faces considerable challenges during thermomechanical processing, particularly in terms of the ambiguous deformation–phase transformation coupling mechanisms and the difficulties in controlling microstructural homogeneity. These issues often lead to coarse-grain ring defects and mechanical property anisotropy in forgings, thereby limiting their applications under extreme service conditions [4,5] . In response to the aerospace industry’s demands for ultra-high strength aluminum alloys with high performance, integrality, large dimension, and complex geometry, breakthroughs must be achieved from two dimensions: material design and preparation technology. On the one hand, high-strength, high-toughness, and high-hardenability thick-section materials are developed through multi-component microalloying design. On the other hand, multi-scale characterization is employed to analyze the dynamic dissolution and precipitation behavior of second-phase particles, and a quantitative relationship model between the processing map and microstructural evolution is established. This provides a theoretical basis for  \noptimizing the solution-aging process window, suppressing the formation of coarse-grain ring defects, and improving the overall service performance of components. While current research priorities focus on establishing constitutive models that incorporate dynamic recovery/recrystallization kinetics and precipitation thermodynamics, it is worth noting that advanced processing map constructio","cbCaisKHfg6yv9iD","https://ap.wps.com/l/cbCaisKHfg6yv9iD","pdf",7396094,17,"English","# 1. Introduction\n## Background and motivation\n## Hot deformation mechanisms and constitutive modeling\n# 2. Experimental methods and conditions\n## Compression test design\n## Range of temperature and strain rate","[{\"question\":\"How were the hot deformation experiments for 7085 aluminum alloy performed?\",\"answer\":\"Compression tests were carried out across temperatures of 593–743 K and strain rates of 0.001–1 s−1, covering varied thermomechanical conditions.\"},{\"question\":\"What softening mechanisms dominate under different deformation conditions?\",\"answer\":\"The true stress–strain response mainly shows dynamic recovery, while higher temperatures combined with lower strain rates shift the dominant softening mechanism toward dynamic recrystallization.\"},{\"question\":\"How is the flow stress predicted in this work and how accurate is it?\",\"answer\":\"A strain-compensated Zener–Hollomon constitutive model is constructed to forecast flow stress, achieving an R2 value of 0.992, indicating exceptional precision.\"}]","Hot Deformation Behavior of 7085 Aluminum Alloy Based on Constitutive Model, Processing Map, and Microstructure Evolution | PDF",1790764296,43,[147,151,155,159],{"page_no":8,"url":148,"width":149,"height":150},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/89d85a7dd1d045a9700b020526a53be1.webp",983,1390,{"page_no":14,"url":152,"width":153,"height":154},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/a7fe5700335fd4d511ef5daab1785d33.webp",982,1388,{"page_no":81,"url":156,"width":157,"height":158},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/94513c3137c0cb1d4c377d1df78b82f0.webp",981,1387,{"page_no":19,"url":160,"width":161,"height":162},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/f65fcd450127c92b5a7ec8b3fd5220c1.webp",980,1385]