[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"detail-sidebar-cat-0-en-105":3,"doc-seo-672148-105":59,"doc-detail-672148-en":133},{"code":4,"msg":5,"data":6},0,"success",[7,13,18,23,28,33,38,43,48,51,55],{"id":8,"doc_module":4,"doc_module_name":9,"category_name":10,"show_sort_weight":11,"slug":12},1,"Document","Story & Novel",90,"story-novel",{"id":14,"doc_module":4,"doc_module_name":9,"category_name":15,"show_sort_weight":16,"slug":17},2,"Literature",80,"literature",{"id":19,"doc_module":4,"doc_module_name":9,"category_name":20,"show_sort_weight":21,"slug":22},4,"Exam",70,"exam",{"id":24,"doc_module":4,"doc_module_name":9,"category_name":25,"show_sort_weight":26,"slug":27},5,"Comic",60,"comic",{"id":29,"doc_module":4,"doc_module_name":9,"category_name":30,"show_sort_weight":31,"slug":32},6,"Technology",50,"technology",{"id":34,"doc_module":4,"doc_module_name":9,"category_name":35,"show_sort_weight":36,"slug":37},7,"Healthcare",40,"healthcare",{"id":39,"doc_module":4,"doc_module_name":9,"category_name":40,"show_sort_weight":41,"slug":42},8,"Research & Report",30,"research-report",{"id":44,"doc_module":4,"doc_module_name":9,"category_name":45,"show_sort_weight":46,"slug":47},9,"Religion & Spirituality",20,"religion-spirituality",{"id":46,"doc_module":4,"doc_module_name":9,"category_name":49,"show_sort_weight":46,"slug":50},"World Cup","world-cup",{"id":52,"doc_module":4,"doc_module_name":9,"category_name":53,"show_sort_weight":52,"slug":54},10,"Lifestyle","lifestyle",{"id":56,"doc_module":4,"doc_module_name":9,"category_name":57,"show_sort_weight":24,"slug":58},19,"General","general",{"code":4,"msg":60,"data":61},"ok",{"site_id":62,"language":63,"slug":64,"title":65,"keywords":66,"description":67,"schema_data":68,"social_meta":126,"head_meta":128,"extra_data":130,"updated_unix":132},105,"en","epoxy-zinc-phosphate-primer-corrosion-resistant-two-pack-coating-specification","Epoxy Zinc Phosphate Primer - Corrosion-Resistant Two-Pack Coating Specification","","Two-pack epoxy zinc phosphate primer specification covering product selection, coating features, color and finish (red oxide/grey, matt to eggshell), typical dry film thickness of 40–50 microns, solids content by volume, theoretical coverage, and temperature limits including continuous 93°C and non-continuous 121°C behavior. Provides substrate preparation for steel using dry abrasive blasting to SSPC-SP10, mixing ratios (A to B 3:1 by volume), pot life guidance, thinning limits for spray, application equipment parameters, required ambient/dew-point conditions, curing schedule at 25–30°C, and restrictions such as non-immersion service and overcoat compatibility.",{"@graph":69,"@context":125},[70,84,104],{"@type":71,"itemListElement":72},"BreadcrumbList",[73,77,79,82],{"item":74,"name":75,"@type":76,"position":8},"https://docshare.wps.com","Home","ListItem",{"item":78,"name":9,"@type":76,"position":14},"https://docshare.wps.com/document/",{"item":80,"name":30,"@type":76,"position":81},"https://docshare.wps.com/document/technology/",3,{"item":83,"name":65,"@type":76,"position":19},"https://docshare.wps.com/document/epoxy-zinc-phosphate-primer-corrosion-resistant-two-pack-coating-specification/672148/",{"url":83,"name":65,"@type":85,"image":86,"author":91,"headline":65,"publisher":94,"fileFormat":97,"inLanguage":63,"description":67,"dateModified":98,"datePublished":98,"encodingFormat":97,"isAccessibleForFree":99,"interactionStatistic":100},"DigitalDocument",{"url":87,"@type":88,"width":89,"height":90},"https://docshare.wps.com/thumbnails/epoxy-zinc-phosphate-primer-corrosion-resistant-two-pack-coating-specification/672148.png","ImageObject",300,407,{"name":92,"@type":93},"Ben ","Person",{"url":74,"name":95,"@type":96},"DocShare","Organization","application/pdf","2026-11-02",true,{"@type":101,"interactionType":102,"userInteractionCount":14},"InteractionCounter",{"@type":103},"ViewAction",{"@type":105,"mainEntity":106},"FAQPage",[107,113,117,121],{"name":108,"@type":109,"acceptedAnswer":110},"What dry film thickness and theoretical coverage rate are specified for the primer?","Question",{"text":111,"@type":112},"The specification calls for 40–50 microns per coat and a theoretical coverage of 9.8 m²/l at 50 microns, accounting for losses during mixing and application.","Answer",{"name":114,"@type":109,"acceptedAnswer":115},"How should the primer be mixed and what is the pot life?",{"text":116,"@type":112},"Mix power separately, then combine and power mix; do not mix partial kits. Use a 3:1 volume ratio (A to B), with pot life about 6 hours at 30°C; pot life ends when the coating loses body and begins to sag.",{"name":118,"@type":109,"acceptedAnswer":119},"What surface preparation is required for steel before applying the primer?",{"text":120,"@type":112},"Surfaces must be clean and dry, with dry abrasive blast to SSPC-SP10 and a 25–30 microns surface profile. Power tool cleaning is acceptable only for touch up.",{"name":122,"@type":109,"acceptedAnswer":123},"What conditions and curing times affect overcoating?",{"text":124,"@type":112},"Application requires substrate temperature above the dew point to avoid flash rusting and adhesion issues. Curing guidance includes minimum overcoating intervals of 9 hours at 25°C and 8 hours at 30°C for a 2.0 mil (50 microns) dry film thickness.","https://schema.org",{"og:url":83,"og:type":127,"og:title":65,"og:site_name":95,"og:description":67},"article",{"robots":129,"canonical":83},"index,follow",{"doc_id":131,"site_id":62},672148,1793586059,{"code":4,"msg":5,"data":134},{"doc_id":131,"user_id":135,"nickname":92,"user_avatar":136,"doc_module":4,"category_id":29,"category_name":30,"doc_title":65,"doc_description":67,"doc_content":137,"file_id":138,"file_url":139,"file_type":140,"file_size":141,"view_count":14,"is_deleted":4,"is_public":8,"is_downloadable":8,"audit_status":8,"page_count":29,"language":142,"language_code":63,"site_id":62,"html_lang":63,"table_of_contents":143,"faqs":144,"seo_title":145,"seo_description":67,"update_tm":132,"read_time":146},2336478951081,"https://ap-avatar.wpscdn.com/davatar_276721f389ce27ea32af1340a28f341c","SELECTION & SPECIFICATION DATA  \nGeneric Type  \nDescription  \nFeatures  \nColor  \nFinish  \nPrimer  \nDry Film Thickness  \nSolids Content  \nTheoretical Coverage Rate  \nDry Temp. Resistance  \nLimitations  \nTopcoats  \nTwo pack epoxy zinc phosphate primer  \nA corrosion resistant primer coat used over steel and inorganic zinc primers. Can be top coated with a broad variety of high performance finish coats.  \n• Excellent corrosion protection  \n• Good abrasion resistance Red oxide and Grey  \nMatt to Eggshell  \nMay be applied over organic and inorganic zinc rich primers. A mist coat may be required to minimize bubbling over zinc rich primers.  \n. 40 to 50 microns per coat  \n.  \n.  \nBy Volume 50 +/-2%  \n9.8 m²/l at 50 microns  \nAllow for loss in mixing and application.  \nContinuous: 200°F (93°C)  \nNon-Continuous: 250°F (121°C)  \nDiscoloration and loss of gloss is observed above 200°F (93°C) .  \nNot recommended for immersion service  \nMay be coated with Epoxies followed by Polyurethanes depending on exposure and need.  \nSUBSTRATES & SURFACE PREPARATION  \nGeneral  \nSteel  \nSurfaces must be clean and dry. Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.  \nDry abrasive blast to SSPC-SP10 with a 25-30 microns surface profile.  \nAcceptable power tool cleaning for touch up only  \nMIXING & THINNING  \nMixing  \nThinning Ratio  \nPot Life  \nPower mix separately, then combine and power mix. DO NOT MIX PARTIAL KITS.  \nUse of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied.  \nSpray: May thin up to (20%) with Thinner 33.  \n3 :1 Ratio by volume (A to B)  \n6 Hours at (30°C) . Pot life ends when coating loses body and begins to sag.  \nPot life times will be less at higher temperatures..  \nAPPLICATION EQUIPMENT GUIDELINES  \nListed below are general equipment guidelines for the application of this product. Job site conditions may require modifications to these guidelines to achieve the desired results.  \nSpray Application  \n(General)  \nConventional Spray  \nAirless Spray  \nBrush  \nRoller  \nThe following spray equipment has been found suitable and is available from manufacturers such as Binks, DeVilbiss and Graco.  \nPressure pot equipped with dual regulators, 3/8” (0 .95 cm) I. D. minimum material hose,  \n0.070 “ fluid tip and appropriate air cap.  \nPump Ratio: 30:1 (min. )  \nGPM Output: 3.0 (min. )  \nMaterial Hose: 3/8” (0 .38 cm) I. D. (min. )  \nTip Size: 0.017-0.021” (0 .043-0.053 cm)  \nOutput PSI: 2100-2300  \nFilter Size: 60 mesh  \nPTFE packings are recommended and available from the pump manufacturer.  \nUse a medium bristle brush. For touch up only.  \nNot recommended.  \nAPPLICATION CONDITIONS  \n\n| Condition | Material | Surface | Ambient | Humidity |\n| --- | --- | --- | --- | --- |\n| Minimum | 40°F (4°C) | 40°F (4°C) | 40°F (4°C) | 0% |\n| Maximum | 90°F (32°C) | 135°F (57°C) | 110°F (43°C) | 90% |\n\nThis product requires the substrate temperature to be above the dew point. Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel and interfere with proper adhesion to the substrate. Special application techniques may be required above or below normal application conditions.  \nCURING SCHEDULE  \n\n| Temperature | Dry to Touch | Hard dry | Over coating Interval |\n| --- | --- | --- | --- |\n| 25Deg C | 60 minutes | 10 hours | Minimum 9 hours |\n| 30 Deg C | 30 minutes | 8 hours | Minimum 8 hours |\n\nThese times are based on a 2.0 mil (50 microns) dry film thickness. Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure. Excessive humidity or condensation on the surface during curing can interfere with the cure, can cause discoloration and may result in a surface haze. Any haze or blush must be removed by water washing before","cbCaigKrJ4lTOMEV","https://ap.wps.com/l/cbCaigKrJ4lTOMEV","pdf",125580,"English","# Selection & Specification Data\n## Features, Color, Finish, Coverage, Resistance, Limitations\n# Substrates & Surface Preparation\n## Steel preparation and cleaning standards\n# Mixing & Thinning\n## Mixing procedure, thinning ratio, pot life\n# Application Equipment Guidelines\n## Spray, brush, roller guidance and equipment specs\n# Application Conditions\n## Ambient limits and dew point requirements\n# Curing Schedule\n## Dry to touch, hard dry, overcoating intervals\n# Cleanup & Safety\n## Thinner/acetone use, ventilation and PPE\n# Packaging, Handling & Storage\n## Shelf life and storage temperature/humidity\n# Warranty","[{\"question\":\"What dry film thickness and theoretical coverage rate are specified for the primer?\",\"answer\":\"The specification calls for 40–50 microns per coat and a theoretical coverage of 9.8 m²/l at 50 microns, accounting for losses during mixing and application.\"},{\"question\":\"How should the primer be mixed and what is the pot life?\",\"answer\":\"Mix power separately, then combine and power mix; do not mix partial kits. Use a 3:1 volume ratio (A to B), with pot life about 6 hours at 30°C; pot life ends when the coating loses body and begins to sag.\"},{\"question\":\"What surface preparation is required for steel before applying the primer?\",\"answer\":\"Surfaces must be clean and dry, with dry abrasive blast to SSPC-SP10 and a 25–30 microns surface profile. Power tool cleaning is acceptable only for touch up.\"},{\"question\":\"What conditions and curing times affect overcoating?\",\"answer\":\"Application requires substrate temperature above the dew point to avoid flash rusting and adhesion issues. Curing guidance includes minimum overcoating intervals of 9 hours at 25°C and 8 hours at 30°C for a 2.0 mil (50 microns) dry film thickness.\"}]","Epoxy Zinc Phosphate Primer - Corrosion-Resistant Two-Pack Coating Specification | PDF",15]