[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"detail-sidebar-cat-0-en-105":3,"doc-seo-662734-105":59,"doc-detail-662734-en":130},{"code":4,"msg":5,"data":6},0,"success",[7,13,18,23,28,33,38,43,48,51,55],{"id":8,"doc_module":4,"doc_module_name":9,"category_name":10,"show_sort_weight":11,"slug":12},1,"Document","Story & Novel",90,"story-novel",{"id":14,"doc_module":4,"doc_module_name":9,"category_name":15,"show_sort_weight":16,"slug":17},2,"Literature",80,"literature",{"id":19,"doc_module":4,"doc_module_name":9,"category_name":20,"show_sort_weight":21,"slug":22},4,"Exam",70,"exam",{"id":24,"doc_module":4,"doc_module_name":9,"category_name":25,"show_sort_weight":26,"slug":27},5,"Comic",60,"comic",{"id":29,"doc_module":4,"doc_module_name":9,"category_name":30,"show_sort_weight":31,"slug":32},6,"Technology",50,"technology",{"id":34,"doc_module":4,"doc_module_name":9,"category_name":35,"show_sort_weight":36,"slug":37},7,"Healthcare",40,"healthcare",{"id":39,"doc_module":4,"doc_module_name":9,"category_name":40,"show_sort_weight":41,"slug":42},8,"Research & Report",30,"research-report",{"id":44,"doc_module":4,"doc_module_name":9,"category_name":45,"show_sort_weight":46,"slug":47},9,"Religion & Spirituality",20,"religion-spirituality",{"id":46,"doc_module":4,"doc_module_name":9,"category_name":49,"show_sort_weight":46,"slug":50},"World Cup","world-cup",{"id":52,"doc_module":4,"doc_module_name":9,"category_name":53,"show_sort_weight":52,"slug":54},10,"Lifestyle","lifestyle",{"id":56,"doc_module":4,"doc_module_name":9,"category_name":57,"show_sort_weight":24,"slug":58},19,"General","general",{"code":4,"msg":60,"data":61},"ok",{"site_id":62,"language":63,"slug":64,"title":65,"keywords":66,"description":67,"schema_data":68,"social_meta":123,"head_meta":125,"extra_data":127,"updated_unix":129},105,"en","ecocam-plotbit-doc-v-101-datasheet","ECOCAM PLOTBIT - Doc. V. 1.01 - Datasheet","","ECOCAM PLOTBIT is a spring-loaded plotter pen for CNC routers, designed for non-rotating use in CNC-controlled systems. The drawing tip compensates height differences to the drawing surface up to 5 mm and allows pressure force adjustment via spring immersion depth. It uses a precise large-capacity refill in multiple colors and line widths, fits common tool holders without height compensation, and requires the workpiece to be fixed on a vacuum table with an appropriate drawing pad or cutting mat. The document provides mounting notes, operating warnings, technical data, available sizes, dimensional drawings, and accessories/spare refills.",{"@graph":69,"@context":122},[70,84,105],{"@type":71,"itemListElement":72},"BreadcrumbList",[73,77,79,82],{"item":74,"name":75,"@type":76,"position":8},"https://docshare.wps.com","Home","ListItem",{"item":78,"name":9,"@type":76,"position":14},"https://docshare.wps.com/document/",{"item":80,"name":30,"@type":76,"position":81},"https://docshare.wps.com/document/technology/",3,{"item":83,"name":65,"@type":76,"position":19},"https://docshare.wps.com/document/ecocam-plotbit-doc-v-101-datasheet/662734/",{"url":83,"name":65,"@type":85,"image":86,"author":91,"headline":65,"publisher":94,"fileFormat":97,"inLanguage":63,"description":67,"dateModified":98,"datePublished":99,"encodingFormat":97,"isAccessibleForFree":100,"interactionStatistic":101},"DigitalDocument",{"url":87,"@type":88,"width":89,"height":90},"https://docshare.wps.com/thumbnails/ecocam-plotbit-doc-v-101-datasheet/662734.png","ImageObject",300,407,{"name":92,"@type":93},"Muffet","Person",{"url":74,"name":95,"@type":96},"DocShare","Organization","application/pdf","2026-10-30","2026-10-28",true,{"@type":102,"interactionType":103,"userInteractionCount":24},"InteractionCounter",{"@type":104},"ViewAction",{"@type":106,"mainEntity":107},"FAQPage",[108,114,118],{"name":109,"@type":110,"acceptedAnswer":111},"How is the ECOCAM PLOTBIT intended to be used in CNC systems?","Question",{"text":112,"@type":113},"Use the PLOTBIT as a plotter pen in CNC-controlled systems. Milling machines can plot large-format drawings with reduced conversion work.","Answer",{"name":115,"@type":110,"acceptedAnswer":116},"What height compensation and immersion limits apply to the drawing tip?",{"text":117,"@type":113},"The tip can compensate height differences up to 5 mm and can be immersed approximately 5 mm into the housing. The immersion depth must never exceed the maximum spring travel of 5 mm.",{"name":119,"@type":110,"acceptedAnswer":120},"What mounting and safety precautions must be followed?",{"text":121,"@type":113},"The PLOTBIT is intended exclusively for non-rotating use, meaning the milling spindle must not rotate while it is in use. There is a risk of injury from flying parts, and the PLOTBIT or work medium could be damaged.","https://schema.org",{"og:url":83,"og:type":124,"og:title":65,"og:site_name":95,"og:description":67},"article",{"robots":126,"canonical":83},"index,follow",{"doc_id":128,"site_id":62},662734,1793222160,{"code":4,"msg":5,"data":131},{"doc_id":128,"user_id":132,"nickname":92,"user_avatar":133,"doc_module":4,"category_id":29,"category_name":30,"doc_title":65,"doc_description":67,"doc_content":134,"file_id":135,"file_url":136,"file_type":137,"file_size":138,"view_count":24,"is_deleted":4,"is_public":8,"is_downloadable":8,"audit_status":8,"page_count":139,"language":140,"language_code":63,"site_id":62,"html_lang":63,"table_of_contents":141,"faqs":142,"seo_title":143,"seo_description":67,"update_tm":129,"read_time":41},962090768927,"https://ap-avatar.wpscdn.com/davatar_085a072bc5b1113ac321206ff7593b45","Spring loaded plotter pen for CNC routers  \nE CO CA M C NC Precision  \nmade in Germany  \n© Copyright  \nECOCAM CNC- Inh. R. Skowron  \nAll previous versions lose their validity with this document. The information in this document is subject to change without notice. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or otherwise, without the express written permission of the copyright owner. Although every care has been taken to avoid mistakes or printing errors, these cannot be ruled out. We would be grateful for any suggestions for improvements or information on possible mistakes or unclear formulation. 01.12.2021  \nE CO CA M C NC ECOCAM PLOTBIT  \n[www.ecocam.de](www.ecocam.de) Doc. V. 1.01 page 2 of 12  \nE CO CA M C NC Precision  \nmade in Germany  \nContent  \n Page  \n1. General description 4  \n1.1 Mounting examples 5  \n1.2 Operating notes 6  \n2. Technical data 7  \n2.1 Available sizes and data 7  \n2.2 Dimensional drawing PLOTBIT 8 mm 8  \n2.3 Dimensional drawing PLOTBIT 10 mm 9  \n2.4 Dimensional drawing PLOTBIT 3/8 inch (9,52 mm) 10  \n2.5 Diagram pressure force / immersion depth 11  \n3. Accessories / Spare refills 12  \nE CO CA M C NC Precision  \nmade in Germany  \n\n|  |\n| --- |\n| 1. General description |\n| The ECOCAM PLOTBIT is a spring-loaded plotter pen that can be used for drawing applications with CNC routers.\u003Cbr>Neither a special mounting nor a separate height compensation is necessary for the use of the PLOTBIT. The drawing tip can compensate height differences to the drawing surface of up to 5mm. |\n| |\n| Despite its small dimensions, the PLOTBIT is equipped with a precise large-capacity refill that is available in various colors and line widths.\u003Cbr>Due to the compact housing dimensions and because of the length of only 65 mm, the PLOTBIT can be used in all common tool holders instead of a milling cutter or drill. |\n\nE CO CA M C NC ECOCAM PLOTBIT  \n[www.ecocam.de](www.ecocam.de) Doc. V. 1.01 page 4 of 12  \nE CO CA M C NC Precision  \nmade in Germany  \n1.1 Mounting examples  \nER20-collet of a milling motor  \nSK40 tool holder  \ncollet of a router  \nVDI30 tool holder  \n| Warning ! | |\n| --- | --- |\n| The ECOCAM PLOTBIT is intended exclusively for non-rotating use. This means that the milling spindle must not rotate while the PLOTBIT is in use. There is a risk of injury from flying parts. The PLOTBIT or the medium to be marked could also be damaged. |  |\n\nE CO CA M C NC ECOCAM PLOTBIT  \n[www.ecocam.de](www.ecocam.de) Doc. V. 1.01 page 5 of 12  \nE CO CA M C NC Precision  \nmade in Germany  \n1.2 Operating notes  \nThe ECOCAM PLOTBIT is intended to be used as a plotter pen in CNC-controlled systems. This means that CNC milling machines can be used for plotting even large-format drawings without extensive conversion work.  \nThe spring-loaded drawing tip can be immersed approx. 5mm deep in the housing. Due to the spring design, the pressure force can also be influenced in this way. The pressure force should be reduced as the material thickness of the paper or drawing board used decreases in order to avoid damaging the drawing paper or board.  \nFor precise results, the material used must be fixed on a vacuum table with an appropriate drawing pad or cutting mat (e.g.: ECOCAM EC4 Art. \\#230200) .  \n| Warning ! | |\n| --- | --- |\n| The immersion depth of the drawing tip must never exceed the maximum spring travel of 5 mm. Otherwise, drawing paper or board, the drawing tip, the PLOTBIT, the drawing pad, the vacuum table or the milling spindle could be damaged. |  |\n\nE CO CA M C NC ECOCAM PLOTBIT  \n[www.ecocam.de](www.ecocam.de) Doc. V. 1.01 page 6 of 12  \nE CO CA M C NC Precision  \nmade in Germany  \n2. Technical data  \n2.1 Available sizes and data  \n\n|  | \\#320010 | \\# 320020 | \\# 320030 |\n| --- | --- | --- | --- |\n|  | PLOTBIT 8 mm | PLOTBIT 10 mm | PLOTBIT 3/8 Inch\u003Cbr>(≈9,52 mm) |\n|  | | | |\n| Housing length without drawing ","cbCaiqP3kB1TsLl0","https://ap.wps.com/l/cbCaiqP3kB1TsLl0","pdf",1737040,12,"English","# 1. General description\n## 1.1 Mounting examples\n## 1.2 Operating notes\n# 2. Technical data\n## 2.1 Available sizes and data\n## 2.2 Dimensional drawing PLOTBIT 8 mm - #320010\n## 2.3 Dimensional drawing PLOTBIT 10 mm - #320020\n## 2.4 Dimensional drawing PLOTBIT 3/8 inch (≈9,52 mm)\n## 2.5 Diagram pressure force / immersion depth\n# 3. Accessories / Spare refills","[{\"question\":\"How is the ECOCAM PLOTBIT intended to be used in CNC systems?\",\"answer\":\"Use the PLOTBIT as a plotter pen in CNC-controlled systems. Milling machines can plot large-format drawings with reduced conversion work.\"},{\"question\":\"What height compensation and immersion limits apply to the drawing tip?\",\"answer\":\"The tip can compensate height differences up to 5 mm and can be immersed approximately 5 mm into the housing. The immersion depth must never exceed the maximum spring travel of 5 mm.\"},{\"question\":\"What mounting and safety precautions must be followed?\",\"answer\":\"The PLOTBIT is intended exclusively for non-rotating use, meaning the milling spindle must not rotate while it is in use. There is a risk of injury from flying parts, and the PLOTBIT or work medium could be damaged.\"}]","ECOCAM PLOTBIT - Doc. V. 1.01 - Datasheet | PDF"]