[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"detail-sidebar-cat-0-en-105":3,"doc-seo-672144-105":59,"doc-detail-672144-en":130},{"code":4,"msg":5,"data":6},0,"success",[7,13,18,23,28,33,38,43,48,51,55],{"id":8,"doc_module":4,"doc_module_name":9,"category_name":10,"show_sort_weight":11,"slug":12},1,"Document","Story & Novel",90,"story-novel",{"id":14,"doc_module":4,"doc_module_name":9,"category_name":15,"show_sort_weight":16,"slug":17},2,"Literature",80,"literature",{"id":19,"doc_module":4,"doc_module_name":9,"category_name":20,"show_sort_weight":21,"slug":22},4,"Exam",70,"exam",{"id":24,"doc_module":4,"doc_module_name":9,"category_name":25,"show_sort_weight":26,"slug":27},5,"Comic",60,"comic",{"id":29,"doc_module":4,"doc_module_name":9,"category_name":30,"show_sort_weight":31,"slug":32},6,"Technology",50,"technology",{"id":34,"doc_module":4,"doc_module_name":9,"category_name":35,"show_sort_weight":36,"slug":37},7,"Healthcare",40,"healthcare",{"id":39,"doc_module":4,"doc_module_name":9,"category_name":40,"show_sort_weight":41,"slug":42},8,"Research & Report",30,"research-report",{"id":44,"doc_module":4,"doc_module_name":9,"category_name":45,"show_sort_weight":46,"slug":47},9,"Religion & Spirituality",20,"religion-spirituality",{"id":46,"doc_module":4,"doc_module_name":9,"category_name":49,"show_sort_weight":46,"slug":50},"World Cup","world-cup",{"id":52,"doc_module":4,"doc_module_name":9,"category_name":53,"show_sort_weight":52,"slug":54},10,"Lifestyle","lifestyle",{"id":56,"doc_module":4,"doc_module_name":9,"category_name":57,"show_sort_weight":24,"slug":58},19,"General","general",{"code":4,"msg":60,"data":61},"ok",{"site_id":62,"language":63,"slug":64,"title":65,"keywords":66,"description":67,"schema_data":68,"social_meta":123,"head_meta":125,"extra_data":127,"updated_unix":129},105,"en","carboguard-893-product-data-sheet-product-data-sheet","Carboguard® 893 Product Data Sheet - Product Data Sheet","","Carboguard® 893 is a cycloaliphatic amine epoxy high-solids corrosion-resistant primer and intermediate coating for steel and inorganic zinc primer systems. It can be used as a primer or intermediate coat and topcoated with high-performance finish coatings. Key properties include excellent corrosion protection, strong film build and edge protection, and good abrasion resistance, with curing down to 40°F (4°C). The sheet specifies dry film thickness ranges, VOC-compliant colors, surface-prep requirements, mixing/thinning guidance, and temperature performance limits. Performance data includes salt fog, water fog, hardness, abrasion, and weatherometer results.",{"@graph":69,"@context":122},[70,84,105],{"@type":71,"itemListElement":72},"BreadcrumbList",[73,77,79,82],{"item":74,"name":75,"@type":76,"position":8},"https://docshare.wps.com","Home","ListItem",{"item":78,"name":9,"@type":76,"position":14},"https://docshare.wps.com/document/",{"item":80,"name":30,"@type":76,"position":81},"https://docshare.wps.com/document/technology/",3,{"item":83,"name":65,"@type":76,"position":19},"https://docshare.wps.com/document/carboguard-893-product-data-sheet-product-data-sheet/672144/",{"url":83,"name":65,"@type":85,"image":86,"author":91,"headline":65,"publisher":94,"fileFormat":97,"inLanguage":63,"description":67,"dateModified":98,"datePublished":99,"encodingFormat":97,"isAccessibleForFree":100,"interactionStatistic":101},"DigitalDocument",{"url":87,"@type":88,"width":89,"height":90},"https://docshare.wps.com/thumbnails/carboguard-893-product-data-sheet-product-data-sheet/672144.png","ImageObject",300,407,{"name":92,"@type":93},"Jasmine","Person",{"url":74,"name":95,"@type":96},"DocShare","Organization","application/pdf","2026-11-03","2026-11-02",true,{"@type":102,"interactionType":103,"userInteractionCount":81},"InteractionCounter",{"@type":104},"ViewAction",{"@type":106,"mainEntity":107},"FAQPage",[108,114,118],{"name":109,"@type":110,"acceptedAnswer":111},"What substrates can Carboguard® 893 be applied to?","Question",{"text":112,"@type":113},"It is intended for clean, dry surfaces including steel, concrete or CMU, and non-ferrous metals. Surface preparation must remove dirt, dust, oil, and contaminants that could interfere with adhesion.","Answer",{"name":115,"@type":110,"acceptedAnswer":116},"How should surfaces be prepared before applying Carboguard® 893?",{"text":117,"@type":113},"Steel requires SSPC-SP6 with a 1.0–2.0 mil (25–50 microns) surface profile. Concrete must be cured 28 days at 75°F (24°C) and 50% relative humidity or equivalent, and prepared following ASTM D42582 and ASTM D4259.",{"name":119,"@type":110,"acceptedAnswer":120},"What are the recommended mixing, thinning, and pot life guidelines?",{"text":121,"@type":113},"Power mix separately, then combine and power mix, and do not mix partial kits. For 1:1 ratio (A to B), pot life is 4 hours at 75°F (24°C) and ends when the coating loses body and begins to sag; higher temperatures shorten pot life.","https://schema.org",{"og:url":83,"og:type":124,"og:title":65,"og:site_name":95,"og:description":67},"article",{"robots":126,"canonical":83},"index,follow",{"doc_id":128,"site_id":62},672144,1793586046,{"code":4,"msg":5,"data":131},{"doc_id":128,"user_id":132,"nickname":92,"user_avatar":133,"doc_module":4,"category_id":29,"category_name":30,"doc_title":65,"doc_description":67,"doc_content":134,"file_id":135,"file_url":136,"file_type":137,"file_size":138,"view_count":81,"is_deleted":4,"is_public":8,"is_downloadable":8,"audit_status":8,"page_count":24,"language":139,"language_code":63,"site_id":62,"html_lang":63,"table_of_contents":140,"faqs":141,"seo_title":142,"seo_description":67,"update_tm":129,"read_time":143},2336478487870,"https://ap-avatar.wpscdn.com/davatar_085a072bc5b1113ac321206ff7593b45","Carboguard® 893  \nPRODUCT DATA SHEET  \nSELECTION & SPECIFICATION DATA  \nGeneric Type  \nDescription  \nFeatures  \nColor  \nFinish  \nPrimer  \nDry Film Thickness  \nSolids Content  \nTheoretical Coverage Rate  \nVOC Values  \nDry Temp. Resistance  \nLimitations  \nTopcoats  \nCycloaliphatic Amine Epoxy  \nHigh solids corrosion resistant primer and intermediate. Used either as a primer or an intermediate coat over steel and inorganic zinc primers. Can be topcoated with a broad variety of high performance finish coats.  \n• Excellent corrosion protection  \n• Excellent film build and edge protection  \n• Used as a primer or an intermediate coating  \n• Good abrasion resistance  \n• Cures down to 40°F (4°C)  \n• VOC compliant to current AIM regulations Gray (0700); Yellow (0600): White (0800) Eggshell  \nSelf-priming. May be applied over organic and inorganic zinc rich primers. A mist coat may be required to minimize bubbling over zinc rich primers.  \n4-6 mils (102-152 microns) per coat  \n3-6 mils (76-150 microns) for mild environments and as an intermediate coat over zinc rich primers.  \n4-6 mils (102-152 microns) for more severe environments.  \nDo not exceed 10.0 mils (250 microns) in a single coat. Excessive film thickness over inorganic zincs may increase damage during shipping or erection.  \nBy Volume 77% +/-2%  \n1235 ft²/gal at 1.0 mils (30.3 m²/l at 25 microns)  \n309 ft²/gal at 4.0 mils (7.6 m²/l at 100 microns)  \n206 ft²/gal at 6.0 mils (5.1 m²/l at 150 microns)  \nAllow for loss in mixing and application.  \nAs Supplied : 1.6 lbs/gal (195 g/l)  \nThinner 230 : 13 oz/gal = 2.1 lbs/gal (252 g/l)  \nThinner 2 : 16 oz/gal = 2.2 lbs/gal (261 g/l)  \nThinner 33 : 32 oz/gal = 2.7 lbs/gal (329 g/l)  \nThese are nominal values and may vary slightly with color. *Maximum thinning for 250 g/l restricted areas is 12 oz/gal with Thinner 2, and 11 oz/gal with Thinner 33 or 230. Use Thinner 76 where nonphotochemically reactive solvents are required (up to 11 oz/gal)  \nContinuous: 200°F (93°C)  \nNon-Continuous: 250°F (121°C)  \nDiscoloration and loss of gloss is observed above 200°F (93°C) .  \nEpoxies may lose gloss, discolor and chalk when exposed to sunlight.  \nNot recommended for immersion service.  \nMay be coated with Acrylics, Epoxies, Alkyds, or Polyurethanes depending on exposure and need.  \nCarboguard® 893  \nPRODUCT DATA SHEET  \nSUBSTRATES & SURFACE PREPARATION  \nGeneral  \nSteel  \nConcrete or CMU  \nNon-Ferrous Metals  \nSurfaces must be clean and dry. Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.  \nSSPC-SP6 with a 1.0-2.0 mil (25-50 microns) surface profile.  \nWhen using under fireproofing products, defer to the primer surface preparation requirements in the product data sheet of the fireproofing product.  \nConcrete must be cured 28 days at 75°F (24°C) and 50% relative humidity or equivalent. Prepare surfaces in accordance with ASTM D42582 Surface Cleaning of Concrete and ASTM D4259 Abrading Concrete. Voids in concrete may require surfacing.  \nSurface profile should be a dense angular 1.5-3 mils and is best achieved through abrasive blasting in accordance with SSPC-SP16 for atmospheric exposure.  \nPERFORMANCE DATA  \nAll test data was generated under laboratory conditions. Field testing results may vary.  \n\n| Test Method | System | Results |\n| --- | --- | --- |\n| ASTM B117 Salt Fog | Blasted Steel 1ct. IOZ 1 ct. 893 | No blistering, rusting and no creepage at scribe after 4000 hours |\n| ASTM D 1735 Water Fog | Blasted Steel 1ct. IOZ 1 ct. 893 | No blistering softening or rusting after 5000 hours |\n| ASTM D2583 Hardness | Blasted Steel 1 ct. 893 | 73, Barcol Test, 1 week cure, 5 mils DFT |\n| ASTM D4060 Abrasion | Blasted Steel 1ct. 893 | 88 mg. loss after 1000 cycles, CS17 wheel, 1000 gm. load |\n| ASTM G26 Weatherometer | Blasted Steel 1ct. IOZ 1 ct. 893 | No blistering softening or rusting after 4000 hours |\n\nTest reports and additional data available upon written request.  \nMI","cbCaiiu9IEi61gtR","https://ap.wps.com/l/cbCaiiu9IEi61gtR","pdf",270593,"English","# Selection & Specification Data\n## Features and Usage\n## Dry Film Thickness, Solids, Coverage, VOC\n## Dry Temperature Resistance and Limitations\n## Topcoats\n# Substrates & Surface Preparation\n## General\n## Steel\n## Concrete or CMU\n## Non-Ferrous Metals\n# Performance Data\n# Mixing & Thinning\n## Mixing\n## Thinning Ratio, Pot Life, Preferred Thinner Uses\n# Application Equipment Guidelines","[{\"question\":\"What substrates can Carboguard® 893 be applied to?\",\"answer\":\"It is intended for clean, dry surfaces including steel, concrete or CMU, and non-ferrous metals. Surface preparation must remove dirt, dust, oil, and contaminants that could interfere with adhesion.\"},{\"question\":\"How should surfaces be prepared before applying Carboguard® 893?\",\"answer\":\"Steel requires SSPC-SP6 with a 1.0–2.0 mil (25–50 microns) surface profile. Concrete must be cured 28 days at 75°F (24°C) and 50% relative humidity or equivalent, and prepared following ASTM D42582 and ASTM D4259.\"},{\"question\":\"What are the recommended mixing, thinning, and pot life guidelines?\",\"answer\":\"Power mix separately, then combine and power mix, and do not mix partial kits. For 1:1 ratio (A to B), pot life is 4 hours at 75°F (24°C) and ends when the coating loses body and begins to sag; higher temperatures shorten pot life.\"}]","Carboguard® 893 Product Data Sheet - Product Data Sheet | PDF",13]