[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"detail-sidebar-cat-0-en-105":3,"doc-seo-648359-105":59,"doc-detail-648359-en":130},{"code":4,"msg":5,"data":6},0,"success",[7,13,18,23,28,33,38,43,48,51,55],{"id":8,"doc_module":4,"doc_module_name":9,"category_name":10,"show_sort_weight":11,"slug":12},1,"Document","Story & Novel",90,"story-novel",{"id":14,"doc_module":4,"doc_module_name":9,"category_name":15,"show_sort_weight":16,"slug":17},2,"Literature",80,"literature",{"id":19,"doc_module":4,"doc_module_name":9,"category_name":20,"show_sort_weight":21,"slug":22},4,"Exam",70,"exam",{"id":24,"doc_module":4,"doc_module_name":9,"category_name":25,"show_sort_weight":26,"slug":27},5,"Comic",60,"comic",{"id":29,"doc_module":4,"doc_module_name":9,"category_name":30,"show_sort_weight":31,"slug":32},6,"Technology",50,"technology",{"id":34,"doc_module":4,"doc_module_name":9,"category_name":35,"show_sort_weight":36,"slug":37},7,"Healthcare",40,"healthcare",{"id":39,"doc_module":4,"doc_module_name":9,"category_name":40,"show_sort_weight":41,"slug":42},8,"Research & Report",30,"research-report",{"id":44,"doc_module":4,"doc_module_name":9,"category_name":45,"show_sort_weight":46,"slug":47},9,"Religion & Spirituality",20,"religion-spirituality",{"id":46,"doc_module":4,"doc_module_name":9,"category_name":49,"show_sort_weight":46,"slug":50},"World Cup","world-cup",{"id":52,"doc_module":4,"doc_module_name":9,"category_name":53,"show_sort_weight":52,"slug":54},10,"Lifestyle","lifestyle",{"id":56,"doc_module":4,"doc_module_name":9,"category_name":57,"show_sort_weight":24,"slug":58},19,"General","general",{"code":4,"msg":60,"data":61},"ok",{"site_id":62,"language":63,"slug":64,"title":65,"keywords":66,"description":67,"schema_data":68,"social_meta":123,"head_meta":125,"extra_data":127,"updated_unix":129},105,"en","cad-standard-manual-facilities-engineering-services-april-2008","CAD Standard Manual - Facilities Engineering Services - April 2008","","CAD Standard Manual for Fermilab Facilities Engineering Services Section (FESS/E) sets out safety-oriented, standardized procedures and minimum requirements for creating consistent, high-quality CAD deliverables for facilities projects. It compiles engineering policies for in-house work and outside A/E consultant utilization, clarifies precedence of A/E subcontract terms, and aligns internal conventions with DOE Order 413.3. The manual specifies document structure, CAD drawing practices, sheet size/title block standards, and electronic naming, layering, color/lineweight mapping, scaling, text/dimensioning, and coordinate system usage.",{"@graph":69,"@context":122},[70,84,105],{"@type":71,"itemListElement":72},"BreadcrumbList",[73,77,79,82],{"item":74,"name":75,"@type":76,"position":8},"https://docshare.wps.com","Home","ListItem",{"item":78,"name":9,"@type":76,"position":14},"https://docshare.wps.com/document/",{"item":80,"name":30,"@type":76,"position":81},"https://docshare.wps.com/document/technology/",3,{"item":83,"name":65,"@type":76,"position":19},"https://docshare.wps.com/document/cad-standard-manual-facilities-engineering-services-april-2008/648359/",{"url":83,"name":65,"@type":85,"image":86,"author":91,"headline":65,"publisher":94,"fileFormat":97,"inLanguage":63,"description":67,"dateModified":98,"datePublished":99,"encodingFormat":97,"isAccessibleForFree":100,"interactionStatistic":101},"DigitalDocument",{"url":87,"@type":88,"width":89,"height":90},"https://docshare.wps.com/thumbnails/cad-standard-manual-facilities-engineering-services-april-2008/648359.png","ImageObject",300,407,{"name":92,"@type":93},"WPS_1790064749","Person",{"url":74,"name":95,"@type":96},"DocShare","Organization","application/pdf","2026-10-26","2026-10-23",true,{"@type":102,"interactionType":103,"userInteractionCount":14},"InteractionCounter",{"@type":104},"ViewAction",{"@type":106,"mainEntity":107},"FAQPage",[108,114,118],{"name":109,"@type":110,"acceptedAnswer":111},"What is the purpose of the CAD Standard Manual?","Question",{"text":112,"@type":113},"It compiles FESS/Engineering policies and procedures to guide CAD deliverables for facilities projects, including work done in-house and by outside A/E consultants.","Answer",{"name":115,"@type":110,"acceptedAnswer":116},"How do A/E subcontract procedures relate to this manual?",{"text":117,"@type":113},"In all cases, the A/E subcontract takes precedence over the procedures in this standard, and this manual acts as a supplement to the subcontract.",{"name":119,"@type":110,"acceptedAnswer":120},"Which CAD formats and software are required for the drawings?",{"text":121,"@type":113},"CAD drawings are to be generated and supplied in DWG format, supported by Autodesk AutoCAD desktop software.","https://schema.org",{"og:url":83,"og:type":124,"og:title":65,"og:site_name":95,"og:description":67},"article",{"robots":126,"canonical":83},"index,follow",{"doc_id":128,"site_id":62},648359,1793030615,{"code":4,"msg":5,"data":131},{"doc_id":128,"user_id":132,"nickname":92,"user_avatar":133,"doc_module":4,"category_id":29,"category_name":30,"doc_title":65,"doc_description":67,"doc_content":134,"file_id":135,"file_url":136,"file_type":137,"file_size":138,"view_count":14,"is_deleted":4,"is_public":8,"is_downloadable":8,"audit_status":8,"page_count":139,"language":140,"language_code":63,"site_id":62,"html_lang":63,"table_of_contents":141,"faqs":142,"seo_title":143,"seo_description":67,"update_tm":144,"read_time":145},3985747859154,"https://ap-avatar.wpscdn.com/davatar_276721f389ce27ea32af1340a28f341c","CAD Standard Manual  \nEngineering Department  \nFacilities Engineering Services Section April 2008  \nThe primary objective at Fermilab is that operations be conducted in a safe, deliberate and controlled manner. The role of the FESS/Engineering (FESS/E) procedures is to provide the best knowledge available in order to accomplish the task.  \nThis CAD Standard Manual provides a compilation of the FESS/Engineering policies and procedures specific to the utilization of in-house projects and projects developed by outside A/E Consultants.  \nThis CAD Standard Manual provides guidance for the A/E Consultant services and is intended as a supplement to the A/E subcontract. In  all cases the A/E subcontract shall take precedence over the procedures in this standard.  \nTo better align with DOE Order 413.3, the following conventions have been revised:  \nTITLE 1 is now Preliminary Design  \nTITLE 2 is now Final Design  \nSECTION I INTRODUCTION  \n1.1 Purpose  \n1.2 Contact Information………………………….. 1  \n1.3 Reference Material…………………………… 1  \nSECTION II GENERAL STANDARDS  \n2.1 Sheet Sizes…………………………………… 2  \n2.2 Title Blocks……………………………………. 3  \n2.3 Font Type……………………………………… 4  \n2.4 Cover Sheet…………………………………… 4  \nSECTION III ELECTRONIC NAMING CONVENTION & FILING  \n3.1 Project Numbering…………………………… 6  \n3.2 Prefix…………………………………………... 7  \n3.3 Suffix…….…………………………………….. 8  \n3.4 Filing…………………………………………… 8  \nSECTION IV LAYER NAMING CONVENTION  \n4.1 Core Layers………………………………….... 10  \n4.2 Discipline Layering..………………………….. 11  \nSECTION V COLOR AND LINE WEIGHT MAPPING  \n5.1 Pen Settings for Sheets D & E………..…….. 12  \n5.2 Pen Settings for Sheets A & B…………….... 12  \nSECTION VI SCALES, TEXT, AND DIMENSIONING  \n6.1 Scales……..…………………………………… 13  \n6.2 Text Styles…………..………………………… 13  \n6.3 Dimensioning…………………………………. 14  \nSECTION VII STANDARD DRAWING TECHIGUES  \n7.1 Section Details & Titles…..………………….. 15  \n7.2 Paper (Layout)/Model Space & XREFs…… 18  \nSECTION VIII FERMI COORDINATE SYSTEM  \n8.1 Definitions……..………………………………. 19  \n8.2 Working with Fermi Coordinate System…… 20  \nSECTION IX AMENDMENTS AND REVISIONS  \n9.1 Definitions..……………………………………. 21  \n9.2 Procedures………....…………………………. 21  \nf  \nCAD STANDARD MANUAL INTRODUCTION  \nI. INTRODUCTION  \n1.1 Purpose:  \nThe following CAD standards were developed by the Facilities Engineering Services Section’s Engineering Department (FESS/E) at Fermilab. The CAD Standards apply to all design, engineering, and construction related (conventional) facilities projects.  \nSection I  \nAlthough FESS/E does not intend to stifle the creativity of individual CAD designers, there is a need to maintain uniformity in the creation of quality design documents. To that end, all CAD drawings should be generated and shall be supplied in DWG format, as supported by Autodesk’s AutoCAD® desktop software. Furthermore, the base building drawing files, especially on retrofitting existing buildings, should be kept in tack with the appropriate viewport scale setting representing the area of work. In this way, the final overall electronic drawing will represent an As-Condition/Record Set.  \nThis document sets forth the minimum requirements to be implemented for all facilities projects, regardless whether projects are completed in-house or work is performed by an outside Architectural and Engineering (A/E) consultant.  \n1.2 Contact Information:  \nInquiries should be directed to:  \nMr. Jim Niehoff  \nFermi National Accelerator Laboratory  \nP.O. Box 500, MS-214 Batavia, IL 60510-0500  \n630.840.3856  \n[niehoff@fnal.gov](niehoff@fnal.gov)  \n1.3 Reference:  \nThe following policies/procurers complement the CAD Standards and should be utilized.  \nA/E Consultant Handbook Design Document Guide Fermilab Engineering Standards GIS Standards Manual  \nPage 1 of 20  \nf  \nCAD STANDARD MANUAL GENERAL STANDARDS  \nII. GENERAL STANDARDS  \nA number of standard sheet sizes and title blocks have been developed to match the nature of various drafting projects completed at Fermilab. The FESS/E Pr","cbCaiqrmHPu37OiT","https://ap.wps.com/l/cbCaiqrmHPu37OiT","pdf",197903,23,"English","# Section I Introduction\n## 1.1 Purpose\n## 1.2 Contact Information\n## 1.3 Reference Material\n# Section II General Standards\n## 2.1 Sheet Sizes\n## 2.2 Title Blocks\n## 2.3 Font Type\n## 2.4 Cover Sheet\n# Section III Electronic Naming Convention & Filing\n## 3.1 Project Numbering\n## 3.2 Prefix\n## 3.3 Suffix\n## 3.4 Filing\n# Section IV Layer Naming Convention\n## 4.1 Core Layers\n## 4.2 Discipline Layering\n# Section V Color and Line Weight Mapping\n## 5.1 Pen Settings for Sheets D & E\n## 5.2 Pen Settings for Sheets A & B\n# Section VI Scales, Text, and Dimensioning\n## 6.1 Scales\n## 6.2 Text Styles\n## 6.3 Dimensioning\n# Section VII Standard Drawing Techniques\n## 7.1 Section Details & Titles\n## 7.2 Paper (Layout)/Model Space & XREFs\n# Section VIII Fermi Coordinate System\n## 8.1 Definitions\n## 8.2 Working with Fermi Coordinate System\n# Section IX Amendments and Revisions\n## 9.1 Definitions\n## 9.2 Procedures","[{\"question\":\"What is the purpose of the CAD Standard Manual?\",\"answer\":\"It compiles FESS/Engineering policies and procedures to guide CAD deliverables for facilities projects, including work done in-house and by outside A/E consultants.\"},{\"question\":\"How do A/E subcontract procedures relate to this manual?\",\"answer\":\"In all cases, the A/E subcontract takes precedence over the procedures in this standard, and this manual acts as a supplement to the subcontract.\"},{\"question\":\"Which CAD formats and software are required for the drawings?\",\"answer\":\"CAD drawings are to be generated and supplied in DWG format, supported by Autodesk AutoCAD desktop software.\"}]","CAD Standard Manual - Facilities Engineering Services - April 2008 | PDF",1792793221,58]