[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"detail-sidebar-cat-0-en-105":3,"doc-seo-466151-105":59,"doc-detail-466151-en":131},{"code":4,"msg":5,"data":6},0,"success",[7,13,18,23,28,33,38,43,48,51,55],{"id":8,"doc_module":4,"doc_module_name":9,"category_name":10,"show_sort_weight":11,"slug":12},1,"Document","Story & Novel",90,"story-novel",{"id":14,"doc_module":4,"doc_module_name":9,"category_name":15,"show_sort_weight":16,"slug":17},2,"Literature",80,"literature",{"id":19,"doc_module":4,"doc_module_name":9,"category_name":20,"show_sort_weight":21,"slug":22},4,"Exam",70,"exam",{"id":24,"doc_module":4,"doc_module_name":9,"category_name":25,"show_sort_weight":26,"slug":27},5,"Comic",60,"comic",{"id":29,"doc_module":4,"doc_module_name":9,"category_name":30,"show_sort_weight":31,"slug":32},6,"Technology",50,"technology",{"id":34,"doc_module":4,"doc_module_name":9,"category_name":35,"show_sort_weight":36,"slug":37},7,"Healthcare",40,"healthcare",{"id":39,"doc_module":4,"doc_module_name":9,"category_name":40,"show_sort_weight":41,"slug":42},8,"Research & Report",30,"research-report",{"id":44,"doc_module":4,"doc_module_name":9,"category_name":45,"show_sort_weight":46,"slug":47},9,"Religion & Spirituality",20,"religion-spirituality",{"id":46,"doc_module":4,"doc_module_name":9,"category_name":49,"show_sort_weight":46,"slug":50},"World Cup","world-cup",{"id":52,"doc_module":4,"doc_module_name":9,"category_name":53,"show_sort_weight":52,"slug":54},10,"Lifestyle","lifestyle",{"id":56,"doc_module":4,"doc_module_name":9,"category_name":57,"show_sort_weight":24,"slug":58},19,"General","general",{"code":4,"msg":60,"data":61},"ok",{"site_id":62,"language":63,"slug":64,"title":65,"keywords":66,"description":67,"schema_data":68,"social_meta":124,"head_meta":126,"extra_data":128,"updated_unix":130},105,"en","assessment-of-macroscopic-properties-based-on-microhardness-measurements-using-the-example-of-the-ticocrfemn-high-entropy-alloy","Assessment of Macroscopic Properties Based on Microhardness Measurements Using the Example of the TiCoCrFeMn High-Entropy Alloy","","The study analyzes mathematical models that determine true hardness from microhardness measurements for the newly designed high-entropy alloy TiCoCrFeMn in the elastic-deformation dominated regime. The PSR model is identified as providing the closest agreement with macroscopic hardness data by accounting for variability in the indenter load’s elastic component. A load-variation analysis reveals a correlation between Young’s modulus and the Meyer coefficient, enabling a model to estimate material parameters from microhardness. The approach is validated on small laboratory specimens and matches crack-length measurement results.",{"@graph":69,"@context":123},[70,84,106],{"@type":71,"itemListElement":72},"BreadcrumbList",[73,77,79,82],{"item":74,"name":75,"@type":76,"position":8},"https://docshare.wps.com","Home","ListItem",{"item":78,"name":9,"@type":76,"position":14},"https://docshare.wps.com/document/",{"item":80,"name":40,"@type":76,"position":81},"https://docshare.wps.com/document/research-report/",3,{"item":83,"name":65,"@type":76,"position":19},"https://docshare.wps.com/document/assessment-of-macroscopic-properties-based-on-microhardness-measurements-using-the-example-of-the-ticocrfemn-high-entropy-alloy/466151/",{"url":83,"name":65,"@type":85,"image":86,"author":91,"headline":65,"publisher":94,"fileFormat":97,"inLanguage":63,"description":67,"dateModified":98,"datePublished":99,"encodingFormat":97,"isAccessibleForFree":100,"interactionStatistic":101},"DigitalDocument",{"url":87,"@type":88,"width":89,"height":90},"https://docshare.wps.com/thumbnails/assessment-of-macroscopic-properties-based-on-microhardness-measurements-using-the-example-of-the-ticocrfemn-high-entropy-alloy/466151.png","ImageObject",300,407,{"name":92,"@type":93},"Chumphorn","Person",{"url":74,"name":95,"@type":96},"DocShare","Organization","application/pdf","2026-10-31","2026-09-30",true,{"@type":102,"interactionType":103,"userInteractionCount":105},"InteractionCounter",{"@type":104},"ViewAction",13,{"@type":107,"mainEntity":108},"FAQPage",[109,115,119],{"name":110,"@type":111,"acceptedAnswer":112},"What is the main goal of the study on TiCoCrFeMn?","Question",{"text":113,"@type":114},"To determine macroscopic (true) hardness from microhardness measurements using mathematical models. The work focuses on the elastic-deformation dominated indentation regime for the TiCoCrFeMn high-entropy alloy.","Answer",{"name":116,"@type":111,"acceptedAnswer":117},"Which model shows the best agreement with macroscopic hardness measurements?",{"text":118,"@type":114},"The PSR model, because it accounts for variability in the elastic component of the applied indenter load. This yields the closest match to macroscopic hardness results.",{"name":120,"@type":111,"acceptedAnswer":121},"How does the indentation size effect affect microhardness testing of TiCoCrFeMn?",{"text":122,"@type":114},"A pronounced indentation size effect is observed, with strong hardness variation across low-load conditions (10–1000 gf). This prevents reliable determination of macroscopic hardness when applying microhardness alone.","https://schema.org",{"og:url":83,"og:type":125,"og:title":65,"og:site_name":95,"og:description":67},"article",{"robots":127,"canonical":83},"index,follow",{"doc_id":129,"site_id":62},466151,1790816160,{"code":4,"msg":5,"data":132},{"doc_id":129,"user_id":133,"nickname":92,"user_avatar":134,"doc_module":4,"category_id":39,"category_name":40,"doc_title":65,"doc_description":67,"doc_content":135,"file_id":136,"file_url":137,"file_type":138,"file_size":139,"view_count":105,"is_deleted":4,"is_public":8,"is_downloadable":8,"audit_status":8,"page_count":140,"language":141,"language_code":63,"site_id":62,"html_lang":63,"table_of_contents":142,"faqs":143,"seo_title":144,"seo_description":67,"update_tm":145,"read_time":146,"preview_page_count":19,"preview_urls":147},2336475401981,"https://ap-avatar.wpscdn.com/avatar/22000c94efd8d5204d?x-image-process=image/resize,m_fixed,w_180,h_180&k=1786935347598174694","Article  \nAssessment of Macroscopic Properties Based on Microhardness Measurements Using the Example of the TiCoCrFeMn  \nHigh-Entropy Alloy  \nDominika Przygucka *, Krzysztof Karczewski , Zbigniew Bojar  and Stanisław Jó´zwiak   \nAcademic Editors: Martina Fracchia and Umberto Anselmi-Tamburini  \nReceived: 24 November 2025  \nRevised: 15 December 2025  \nAccepted: 19 December 2025  \nPublished: 29 December 2025  \nCopyright: © 2025 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license.  \nFaculty of Advanced Technologies and Chemistry, Military University of Technology, Sylwestra Kaliskiego 2,  \n00-908 Warsaw, Poland; [krzysztof.karczewski@wat.edu.pl](krzysztof.karczewski@wat.edu.pl) (K.K.); [zbigniew.bojar@wat.edu.pl](zbigniew.bojar@wat.edu.pl) (Z.B.);  \n[stanislaw.jozwiak@wat.edu.pl](stanislaw.jozwiak@wat.edu.pl) (S.J.)  \n* Correspondence: [dominika.przygucka@wat.edu.pl](dominika.przygucka@wat.edu.pl)  \nAbstract  \nIn this study, using the newly designed high-entropy alloy TiCoCrFeMn as an example, mathematical models for determining the true hardness from microhardness measurements in the regime dominated by elastic deformation were analyzed. It was found that the PSR model, which accounts for the variability in the elastic component of the applied indenter load, provides the best agreement with macroscopic hardness measurements. Analysis of the load variation law revealed a correlation between the Young’s modulus and the Meyer coefficient, which formed the basis for developing a model for determining this material parameter from microhardness measurements. The proposed methodology, applicable to small laboratory specimens, was shown to be consistent with the results obtained from crack-length measurements.  \nKeywords: high-entropy alloys; true hardness; young modulus  \n1. Introduction  \nIn early-stage research, new materials are commonly investigated at a microscale due to limited sample availability, which enables only a preliminary evaluation of their structure, thermal stability, and selected mechanical properties. While structural characterization can be performed on very small specimens, mechanical testing is considerably more difficult. Consequently, hardness measurements—particularly the Vickers method—are widely used as a rapid, simple, and minimally destructive means of initial mechanical assessment. Although hardness is not a fundamental material constant, it correlates with tensile strength, yield strength, and elastic behavior [1] . As such, hardness provides insight into microstructural uniformity and the effectiveness of processing steps such as heat treatment [2], plastic deformation, or thermochemical processing. Hardness data are also applied to evaluate service-induced degradation and estimate remaining lifetime [3] .  \nEmpirical studies indicate that the hardness-to-tensile strength ratio typically ranges from 2.3 to 3.7 . More specific relationships include [4]:  \n(1) Annealed materials: 3σYS \u003C HV\u003C 3σUTS;  \n(2) Work-hardened materials: HV≈ 3σYS;  \n(3) HPT-processed alloys: HV \u003C 3σYS .  \nHowever, hardness results depend strongly on the measurement method, load, and indenter geometry. A reliable comparison is possible only under consistent testing con-  \nditions that satisfy Kick’s similarity law. Load-independent Vickers hardness requires similarity in plastic deformation, a condition rarely met in practice. Surface heterogeneity and indenter–material friction may further influence the results. These limitations are critical for very small samples, where macroscopic loads cannot be applied [1] . Microhardness testing at low loads increases the elastic contribution to indentation, thereby increasing measurement scatter. The well-known indentation size effect (ISE)—an apparent hardness increase with decreasing load—arises from the nonlinear partitioning of elastic and plastic deformati","cbCaifJo3nSZH7X6","https://ap.wps.com/l/cbCaifJo3nSZH7X6","pdf",5623925,25,"English","# Introduction\n## Microhardness and hardness: role and limitations\n## Indentation size effect and testing constraints\n## Modeling approaches for true hardness","[{\"question\":\"What is the main goal of the study on TiCoCrFeMn?\",\"answer\":\"To determine macroscopic (true) hardness from microhardness measurements using mathematical models. The work focuses on the elastic-deformation dominated indentation regime for the TiCoCrFeMn high-entropy alloy.\"},{\"question\":\"Which model shows the best agreement with macroscopic hardness measurements?\",\"answer\":\"The PSR model, because it accounts for variability in the elastic component of the applied indenter load. This yields the closest match to macroscopic hardness results.\"},{\"question\":\"How does the indentation size effect affect microhardness testing of TiCoCrFeMn?\",\"answer\":\"A pronounced indentation size effect is observed, with strong hardness variation across low-load conditions (10–1000 gf). This prevents reliable determination of macroscopic hardness when applying microhardness alone.\"}]","Assessment of Macroscopic Properties Based on Microhardness Measurements Using the Example of the TiCoCrFeMn High-Entropy Alloy | PDF",1790770667,63,[148,152,156,160],{"page_no":8,"url":149,"width":150,"height":151},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/9ee90f22f08e56175bbda655ef1cc187.webp",983,1390,{"page_no":14,"url":153,"width":154,"height":155},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/2cc8da087c4d582fdd619e76434e13e6.webp",982,1388,{"page_no":81,"url":157,"width":158,"height":159},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/620cd44bf1e78a35e41880075761b5ea.webp",981,1387,{"page_no":19,"url":161,"width":162,"height":163},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/07d6d9bdf8c1522a23cdedfd7bf9a384.webp",980,1385]