[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"detail-sidebar-cat-0-en-105":3,"doc-seo-560286-105":59,"doc-detail-560286-en":130},{"code":4,"msg":5,"data":6},0,"success",[7,13,18,23,28,33,38,43,48,51,55],{"id":8,"doc_module":4,"doc_module_name":9,"category_name":10,"show_sort_weight":11,"slug":12},1,"Document","Story & Novel",90,"story-novel",{"id":14,"doc_module":4,"doc_module_name":9,"category_name":15,"show_sort_weight":16,"slug":17},2,"Literature",80,"literature",{"id":19,"doc_module":4,"doc_module_name":9,"category_name":20,"show_sort_weight":21,"slug":22},4,"Exam",70,"exam",{"id":24,"doc_module":4,"doc_module_name":9,"category_name":25,"show_sort_weight":26,"slug":27},5,"Comic",60,"comic",{"id":29,"doc_module":4,"doc_module_name":9,"category_name":30,"show_sort_weight":31,"slug":32},6,"Technology",50,"technology",{"id":34,"doc_module":4,"doc_module_name":9,"category_name":35,"show_sort_weight":36,"slug":37},7,"Healthcare",40,"healthcare",{"id":39,"doc_module":4,"doc_module_name":9,"category_name":40,"show_sort_weight":41,"slug":42},8,"Research & Report",30,"research-report",{"id":44,"doc_module":4,"doc_module_name":9,"category_name":45,"show_sort_weight":46,"slug":47},9,"Religion & Spirituality",20,"religion-spirituality",{"id":46,"doc_module":4,"doc_module_name":9,"category_name":49,"show_sort_weight":46,"slug":50},"World Cup","world-cup",{"id":52,"doc_module":4,"doc_module_name":9,"category_name":53,"show_sort_weight":52,"slug":54},10,"Lifestyle","lifestyle",{"id":56,"doc_module":4,"doc_module_name":9,"category_name":57,"show_sort_weight":24,"slug":58},19,"General","general",{"code":4,"msg":60,"data":61},"ok",{"site_id":62,"language":63,"slug":64,"title":65,"keywords":66,"description":67,"schema_data":68,"social_meta":123,"head_meta":125,"extra_data":127,"updated_unix":129},105,"en","an-6611-binarybcd-gain-programmed-amplifiers-programmable-gain-amplifier-overview","AN-6611 - Binary/BCD Gain Programmed Amplifiers - Programmable gain amplifier overview","","AN-6611 describes logic controlled Gain Programmable Amplifiers (GPA) for signal preconditioning, level control, and dynamic range expansion, focusing on accuracy, speed, and signal handling limits of conventional CMOS and improved current-mode approaches. It explains the GPA as a multiplying digital-to-analog converter (multiplying D/A), using monolithic current mode analog switches, an op amp, and resistors to achieve large signal handling up to ±25 V while simplifying logic interfacing. Practical design constraints, gain accuracy, resistor tolerance effects, and example 4-bit and 8-bit binary/BCD implementations are discussed, with guidance on switch drive and scaling.",{"@graph":69,"@context":122},[70,84,105],{"@type":71,"itemListElement":72},"BreadcrumbList",[73,77,79,82],{"item":74,"name":75,"@type":76,"position":8},"https://docshare.wps.com","Home","ListItem",{"item":78,"name":9,"@type":76,"position":14},"https://docshare.wps.com/document/",{"item":80,"name":40,"@type":76,"position":81},"https://docshare.wps.com/document/research-report/",3,{"item":83,"name":65,"@type":76,"position":19},"https://docshare.wps.com/document/an-6611-binarybcd-gain-programmed-amplifiers-programmable-gain-amplifier-overview/560286/",{"url":83,"name":65,"@type":85,"image":86,"author":91,"headline":65,"publisher":94,"fileFormat":97,"inLanguage":63,"description":67,"dateModified":98,"datePublished":99,"encodingFormat":97,"isAccessibleForFree":100,"interactionStatistic":101},"DigitalDocument",{"url":87,"@type":88,"width":89,"height":90},"https://docshare.wps.com/thumbnails/an-6611-binarybcd-gain-programmed-amplifiers-programmable-gain-amplifier-overview/560286.png","ImageObject",300,407,{"name":92,"@type":93},"Alex Sinclair","Person",{"url":74,"name":95,"@type":96},"DocShare","Organization","application/pdf","2026-11-19","2026-10-12",true,{"@type":102,"interactionType":103,"userInteractionCount":39},"InteractionCounter",{"@type":104},"ViewAction",{"@type":106,"mainEntity":107},"FAQPage",[108,114,118],{"name":109,"@type":110,"acceptedAnswer":111},"Why do conventional CMOS analog switches limit GPA performance?","Question",{"text":112,"@type":113},"Conventional CMOS analog switches limit signal handling to about ±7.5 V and accuracy to around 1%. Higher-voltage alternatives improve signal range but increase cost and still may not match the highest capability.","Answer",{"name":115,"@type":110,"acceptedAnswer":116},"How is a logic controlled GPA implemented in this document?",{"text":117,"@type":113},"It is treated as a multiplying digital-to-analog converter (multiplying D/A), where a reference node is multiplied by the digital input. Current mode analog switches steer signal current at the op-amp virtual ground, with resistor feedback setting the gain.",{"name":119,"@type":110,"acceptedAnswer":120},"What design parameters most strongly affect gain accuracy in the converter?",{"text":121,"@type":113},"Resistor values and their tolerance directly impact output gain and errors. The document explains that using appropriate tolerances for the feedback and weighted resistors can achieve effective accuracy targets while supporting higher-resolution (e.g., 8-bit) operation.","https://schema.org",{"og:url":83,"og:type":124,"og:title":65,"og:site_name":95,"og:description":67},"article",{"robots":126,"canonical":83},"index,follow",{"doc_id":128,"site_id":62},560286,1793117872,{"code":4,"msg":5,"data":131},{"doc_id":128,"user_id":132,"nickname":92,"user_avatar":133,"doc_module":4,"category_id":39,"category_name":40,"doc_title":65,"doc_description":67,"doc_content":134,"file_id":135,"file_url":136,"file_type":137,"file_size":138,"view_count":39,"is_deleted":4,"is_public":8,"is_downloadable":8,"audit_status":8,"page_count":81,"language":139,"language_code":63,"site_id":62,"html_lang":63,"table_of_contents":140,"faqs":141,"seo_title":142,"seo_description":67,"update_tm":143,"read_time":39,"preview_page_count":81,"preview_urls":144},1099523882182,"https://ap-avatar.wpscdn.com/davatar_6f874abed73319feea01a86fa6f0fab8","[www.fairchildsemi.com](www.fairchildsemi.com)  \nAN-6611  \nBinary/BCD Gain Programmed Amplifiers  \nMany systems require logic controlled Gain Programmable Amplifiers (GPA) for signal preconditioning, level control and dynamic range expansion. The system sets GPA requirements for accuracy, speed and signal handling capability, limiting the type used. Conventional CMOS analog switches limit signal handling to ±7.5 V and accuracy to 1% . High voltage CMOS or JFET analog switches increase both accuracy and signal handling (±10 V to ±15 V) but at a greater cost. Programmable amplifiers using current mode analog switches have the highest signal handling capability (±25 V) with high accuracy, speed and low cost.  \nIn reality, the logic controlled GPA is a multiplying digitalto-analog converter (multiplying D/A) . The D/A input is the reference node which is multiplied by the digital input. Multiplying D/A converters have been available for sometime in module, hybrid and monolithic form but suffer from high cost and poor signal handling capability (±10 V maximum) .  \nLarge signal handling (±25 V), moderate cost multiplying D/A converters can be built using monolithic current mode analog switches, an op amp and a few resistors.  \nUnlike conventional analog switches, only signal current is switched at the virtual ground of an op amp with current mode analog switches. Limiting the voltage across the switch to a few hundred millivolts, power supplies, logic interface and level translator circuits are eliminated allowing the JFET switches to be driven directly by standard logic.  \nFigure 1. Current Mode Analog Switch  \nA logic \"0\" turns the switch ON with a logic \"1\" shutting the switch OFF by pinching the JFET OFF. The diode is used toclamp the source to drain voltage to about 0.7 V in the switch OFF state. The series JFET in the feedback path is used to compensate for the ON resistance of the switch JFET.  \nCurrent through the switch is determined by the input resistor, R1, the switch ON resistance and the input voltage, VIN. Scaling of the output voltage is accomplished with the feedback resistor, setting the gain of the amplifier.  \nA 4-bit multiplying D/A converter can be built using a quad current mode switch, 4 binary weighted resistors (R, 2R, 4R, and 8R) and an op amp. The output voltage will be a function of the feedback resistor, input resistors and the logic state of the JFET gates, GN.  \nThe number of bits is expanded by cascading another quad current switch and resistor array to the first. Instead of continuing the binary progression of the input resistors,(16R, 32R, etc), current splitting resistors are used such that the same resistor array (R, 2R, 4R, 8R) is used for the additional bits, minimizing the number of resistor values required for higher order converters.  \nFigure 2. 4-Bit Multiplying D/A Converter  \nFigure 3. 8-Bit Multiplying D/A Using Cascaded 4-Bit Sections  \nBinary weighting requires a 1/16 current split for the second switch quad while BCD weighting requires a 1/10 split.  \nThere are two basic switch configurations available that are optimized for a variety of logic drives: TTL or CMOS Multiple independent switches (four by SPST) and a four channel multiplex version with a series compensation JFET.  \nPractical limitations in using monolithic current mode analog switches need consideration. Resistor values and tolerance impacted by switch resistance is minimized by increasing resistor values without regard, but limits bandwidth and creates leakage errors at elevated temperatures. Using resistors that are too small, increases switch resistance errors. Current saturation (increased switch resistance) occurs when the switch current approaches the JFET saturation current, IDSS. High currents also cause IG(ON), current lost through the gate, as the diode and JFET source to gate diode become forward biased. An input resistor value of 10 k limits the switch current to less than 2 mA minimizing both leakage and swit","cbCaitNZoRIFC8aH","https://ap.wps.com/l/cbCaitNZoRIFC8aH","pdf",303222,"English","# Binary/BCD Gain Programmable Amplifiers\n## Logic controlled GPA and multiplying D/A concept\n## Building blocks: current mode analog switches and op-amp feedback\n## 4-bit and cascaded 8-bit binary/BCD multiplying D/A\n## Switch configurations and logic drive options\n## Practical limitations and component value guidance\n## Gain accuracy, resolution, and resistor tolerance analysis\n## Example designs and adjustable gain/attenuation","[{\"question\":\"Why do conventional CMOS analog switches limit GPA performance?\",\"answer\":\"Conventional CMOS analog switches limit signal handling to about ±7.5 V and accuracy to around 1%. Higher-voltage alternatives improve signal range but increase cost and still may not match the highest capability.\"},{\"question\":\"How is a logic controlled GPA implemented in this document?\",\"answer\":\"It is treated as a multiplying digital-to-analog converter (multiplying D/A), where a reference node is multiplied by the digital input. Current mode analog switches steer signal current at the op-amp virtual ground, with resistor feedback setting the gain.\"},{\"question\":\"What design parameters most strongly affect gain accuracy in the converter?\",\"answer\":\"Resistor values and their tolerance directly impact output gain and errors. The document explains that using appropriate tolerances for the feedback and weighted resistors can achieve effective accuracy targets while supporting higher-resolution (e.g., 8-bit) operation.\"}]","AN-6611 - Binary/BCD Gain Programmed Amplifiers - Programmable gain amplifier overview | PDF",1791802616,[145,149,153],{"page_no":8,"url":146,"width":147,"height":148},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/51717d549e7223c469c244b78ba85a24.webp",983,1272,{"page_no":14,"url":150,"width":151,"height":152},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/36beff118118ff2e7f5ae6bb8b1fa799.webp",982,1270,{"page_no":81,"url":154,"width":155,"height":156},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/65e84a5068a8ebda7c630a285529e41f.webp",981,1269]