[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"doc-seo-366698-105":3,"detail-sidebar-cat-0-en-105":81,"doc-detail-366698-en":130},{"code":4,"msg":5,"data":6},0,"ok",{"site_id":7,"language":8,"slug":9,"title":10,"keywords":11,"description":12,"schema_data":13,"social_meta":74,"head_meta":76,"extra_data":78,"updated_unix":80},105,"en","aluminum-site-rite-hand-benders-840a-841a-842a-843a-840ah-841ah-and-842ah-and-iron-site-rite-hand-benders-840f-841f-842f-843f-840fh-841fh-and-842fh-instruction-manual","ALUMINUM - SITE-RITE® Hand Benders 840A, 841A, 842A, 843A, 840AH, 841AH and 842AH - AND IRON SITE-RITE® Hand Benders 840F, 841F, 842F, 843F, 840FH, 841FH, and 842FH - Instruction Manual","","Instruction manual for Greenlee aluminum and iron SITE-RITE® hand benders, covering models 840A/841A/842A/843A/840AH/841AH/842AH and 840F/841F/842F/843F/840FH/841FH/842FH. Provides safety guidance, qualification requirements for operators, inspection and replacement of worn components, and proper use for bending specified conduit ranges. Includes step-by-step bending procedures for handle-up and handle-down techniques, marking for 90° stubs with deduct length, correcting overbends, back-to-back 90° stubs, offset bending using Greenlee offset table data, and working past obstructions while referencing required center-to-center measurements.",{"@graph":14,"@context":73},[15,34,56],{"@type":16,"itemListElement":17},"BreadcrumbList",[18,23,27,31],{"item":19,"name":20,"@type":21,"position":22},"https://docshare.wps.com","Home","ListItem",1,{"item":24,"name":25,"@type":21,"position":26},"https://docshare.wps.com/document/","Document",2,{"item":28,"name":29,"@type":21,"position":30},"https://docshare.wps.com/document/technology/","Technology",3,{"item":32,"name":10,"@type":21,"position":33},"https://docshare.wps.com/document/aluminum-site-rite-hand-benders-840a-841a-842a-843a-840ah-841ah-and-842ah-and-iron-site-rite-hand-benders-840f-841f-842f-843f-840fh-841fh-and-842fh-instruction-manual/366698/",4,{"url":32,"name":10,"@type":35,"image":36,"author":41,"headline":10,"publisher":44,"fileFormat":47,"inLanguage":8,"description":12,"dateModified":48,"datePublished":49,"encodingFormat":47,"isAccessibleForFree":50,"interactionStatistic":51},"DigitalDocument",{"url":37,"@type":38,"width":39,"height":40},"https://docshare.wps.com/thumbnails/aluminum-site-rite-hand-benders-840a-841a-842a-843a-840ah-841ah-and-842ah-and-iron-site-rite-hand-benders-840f-841f-842f-843f-840fh-841fh-and-842fh-instruction-manual/366698.png","ImageObject",300,407,{"name":42,"@type":43},"Fans","Person",{"url":19,"name":45,"@type":46},"DocShare","Organization","application/pdf","2026-10-21","2026-09-23",true,{"@type":52,"interactionType":53,"userInteractionCount":55},"InteractionCounter",{"@type":54},"ViewAction",10,{"@type":57,"mainEntity":58},"FAQPage",[59,65,69],{"name":60,"@type":61,"acceptedAnswer":62},"What tools and conduit sizes are these SITE-RITE® hand benders intended for?","Question",{"text":63,"@type":64},"The aluminum SITE-RITE® and iron SITE-RITE® benders are intended to bend 1/2\" through 1-1/4\" EMT and 1/2\" through 1\" rigid and IMC conduit.","Answer",{"name":66,"@type":61,"acceptedAnswer":67},"How should an operator align and bend when using the handle-up method?",{"text":68,"@type":64},"Mark the conduit, insert it with the arrow aligned to the bending mark, apply heavy foot pressure on the bending shoe, and stop when the pin aligns with the appropriate angle mark. Rigid conduit should be slightly overbent to compensate for springback.",{"name":70,"@type":61,"acceptedAnswer":71},"How do you determine an offset when rerouting around an obstruction?",{"text":72,"@type":64},"An offset consists of two equal opposing bends. Select the offset angle by considering that steeper angles require more pulling force and shallower angles require more space, then use the Greenlee offset table values to work out the needed offset depth and center-to-center distance.","https://schema.org",{"og:url":32,"og:type":75,"og:title":10,"og:site_name":45,"og:description":12},"article",{"robots":77,"canonical":32},"index,follow",{"doc_id":79,"site_id":7},366698,1790469656,{"code":4,"msg":82,"data":83},"success",[84,88,92,96,101,105,110,115,120,123,126],{"id":22,"doc_module":4,"doc_module_name":25,"category_name":85,"show_sort_weight":86,"slug":87},"Story & Novel",90,"story-novel",{"id":26,"doc_module":4,"doc_module_name":25,"category_name":89,"show_sort_weight":90,"slug":91},"Literature",80,"literature",{"id":33,"doc_module":4,"doc_module_name":25,"category_name":93,"show_sort_weight":94,"slug":95},"Exam",70,"exam",{"id":97,"doc_module":4,"doc_module_name":25,"category_name":98,"show_sort_weight":99,"slug":100},5,"Comic",60,"comic",{"id":102,"doc_module":4,"doc_module_name":25,"category_name":29,"show_sort_weight":103,"slug":104},6,50,"technology",{"id":106,"doc_module":4,"doc_module_name":25,"category_name":107,"show_sort_weight":108,"slug":109},7,"Healthcare",40,"healthcare",{"id":111,"doc_module":4,"doc_module_name":25,"category_name":112,"show_sort_weight":113,"slug":114},8,"Research & Report",30,"research-report",{"id":116,"doc_module":4,"doc_module_name":25,"category_name":117,"show_sort_weight":118,"slug":119},9,"Religion & Spirituality",20,"religion-spirituality",{"id":118,"doc_module":4,"doc_module_name":25,"category_name":121,"show_sort_weight":118,"slug":122},"World Cup","world-cup",{"id":55,"doc_module":4,"doc_module_name":25,"category_name":124,"show_sort_weight":55,"slug":125},"Lifestyle","lifestyle",{"id":127,"doc_module":4,"doc_module_name":25,"category_name":128,"show_sort_weight":97,"slug":129},19,"General","general",{"code":4,"msg":82,"data":131},{"doc_id":79,"user_id":132,"nickname":42,"user_avatar":133,"doc_module":4,"category_id":102,"category_name":29,"doc_title":10,"doc_description":12,"doc_content":134,"file_id":135,"file_url":136,"file_type":137,"file_size":138,"view_count":55,"is_deleted":4,"is_public":22,"is_downloadable":22,"audit_status":22,"page_count":55,"language":139,"language_code":8,"site_id":7,"html_lang":8,"table_of_contents":140,"faqs":141,"seo_title":142,"seo_description":12,"update_tm":143,"read_time":144},5909892330395,"https://ap-avatar.wpscdn.com/davatar_6f874abed73319feea01a86fa6f0fab8","INSTRUCTION MANUAL  \nALUMINUM SITE-RITE®  \nHAND BENDERS 840A, 841A, 842A, 843A, 840AH, 841AH and 842AH  \nAND  \nIRON SITE-RITE® HAND BENDERS  \n840F, 841F, 842F, 843F, 840FH, 841FH, and 842FH  \n\n| | Read and understand this material before operating or servicing this equipment. Failure to understand how to safely operate this tool could result in an accident causing serious injury or death. |\n| --- | --- |\n\n52034125 © 2008 Greenlee Textron Inc. 4/08  \n1.800.561.8187 www.  . com [information@itm.com](information@itm.com)  \nDescription  \nThe Greenlee aluminum SITE-RITE® and iron SITE-RITE® benders are manually powered tools intended to bend 1/2\" through 1-1/4\" EMT (electrical metallic tubing) and 1/2\" through 1\" rigid and IMC conduit.  \nPurpose  \nThis instruction manual is intended to familiarize operators and maintenance personnel with the safe operation of the Greenlee  \nSITE-RITE® Manual Benders. This manual should be kept available to all operating personnel.  \n\n| | |  |\n| --- | --- | --- |\n|  | A person who has not read and does not understand all operating instructions is not qualified to operate this tool.\u003Cbr>Failure to read and understand safety instructions may result in injury or property damage. |  |\n\n\n| |\n| --- |\n| Inspect the tool for wear or damage. Replace worn, damaged, or missing components with Greenlee replacement parts. A worn, damaged, or improperly assembled component may fail, resulting in injury or property damage. |\n\n\n| |\n| --- |\n| Use this tool for manufacturer’s intended use only. Use other than that for which the tool was intended may result in injury. |\n\nAll specifications are nominal and may change as design improvements occur. Greenlee Textron Inc. shall not be liable for damages resulting from misapplication or misuse of its products.  \nKEEP THIS MANUAL  \nAdditional copies of this manual are available upon request at no charge.  \n2 Greenlee / A Textron Company  \n1.800.561.8187 www.  . com [information@itm.com](information@itm.com)  \nBending—Handle Up  \n1. Mark the conduit.  \n2. Insert the conduit into the bender so that the arrow is aligned with the bending mark.  \n3. Place one foot on the bender as illustrated. Use heavy foot pressure on the bending shoe; maintain this pressure throughout the bend.  \n4. Look down the line of sight as illustrated. Stop bending when the pin is in line with the appropriate angle mark.  \nNote: Overbend rigid conduit slightly to compensate for springback.  \nBending—Handle Down  \n3  \n1.800.561.8187 www.  . com [information@itm.com](information@itm.com)  \nBending—Handle Down (cont’d)  \n1. Mark the conduit.  \n2. Insert the conduit into the bender so that the arrow is aligned with the bending mark.  \n3. Position the bender as shown, with your body as close to the benderas possible.  \n4. With the handle angled to prevent slipping, apply constant pressure against the conduit throughout the bend.  \n5. Bend until the edge of the conduit is in line with the degree scale as illustrated.  \nNote: Overbend rigid conduit slightly to compensate for springback.  \nBending Tips:  \n• Line up all bends in the same plane.  \n• Bend 1/2\" and 3/4\" EMT with the handle down.  \n• Bend 1\" and 1-1/4\" conduit with the handle up.  \n• When bending with the handle up, work at a stairwell or loading dock so that previously made bends hang over the edge.  \nMarking the Conduit for 90° Stubs  \n1. Measure the length of the required stub.  \n2. Measure and mark the stub length on the conduit. This is Mark A.  \n3. See the Deduct length shown on the bender. Subtract the Deduct length from Mark A and make a new mark. This is Mark B.  \n4. Align Mark B with the arrow on the bender and bend the conduit to 90° .  \n4 Greenlee / A Textron Company  \n1.800.561.8187 www.  . com [information@itm.com](information@itm.com)  \nCorrecting Overbends  \nIf a stub-up is accidentally overbent, place the open end of the bender handle over the conduit and manipulate to desired angle.  \nBack-to-Back 90° Stubs  \n1. Make the first 90° stub","cbCaiiuTyURckIVc","https://ap.wps.com/l/cbCaiiuTyURckIVc","pdf",522842,"English","# Description\n# Purpose\n# Safety and Qualification\n# Pre-Operation Checks\n# Bending Procedures\n## Handle Up\n## Handle Down\n# Bending Tips\n# Marking for 90° Stubs\n# Correcting Overbends\n# Back-to-Back 90° Stubs\n# Offset Bends\n## Working Past an Obstruction","[{\"question\":\"What tools and conduit sizes are these SITE-RITE® hand benders intended for?\",\"answer\":\"The aluminum SITE-RITE® and iron SITE-RITE® benders are intended to bend 1/2\\\" through 1-1/4\\\" EMT and 1/2\\\" through 1\\\" rigid and IMC conduit.\"},{\"question\":\"How should an operator align and bend when using the handle-up method?\",\"answer\":\"Mark the conduit, insert it with the arrow aligned to the bending mark, apply heavy foot pressure on the bending shoe, and stop when the pin aligns with the appropriate angle mark. Rigid conduit should be slightly overbent to compensate for springback.\"},{\"question\":\"How do you determine an offset when rerouting around an obstruction?\",\"answer\":\"An offset consists of two equal opposing bends. Select the offset angle by considering that steeper angles require more pulling force and shallower angles require more space, then use the Greenlee offset table values to work out the needed offset depth and center-to-center distance.\"}]","ALUMINUM - SITE-RITE® Hand Benders 840A, 841A, 842A, 843A, 840AH, 841AH and 842AH - AND IRON SITE-RITE® Hand Benders 840F, 841F, 842F, 843F, 840FH, 841FH, and 842FH - Instruction Manual | PDF",1790166766,25]