[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"detail-sidebar-cat-0-en-105":3,"doc-seo-341377-105":59,"doc-detail-341377-en":131},{"code":4,"msg":5,"data":6},0,"success",[7,13,18,23,28,33,38,43,48,51,55],{"id":8,"doc_module":4,"doc_module_name":9,"category_name":10,"show_sort_weight":11,"slug":12},1,"Document","Story & Novel",90,"story-novel",{"id":14,"doc_module":4,"doc_module_name":9,"category_name":15,"show_sort_weight":16,"slug":17},2,"Literature",80,"literature",{"id":19,"doc_module":4,"doc_module_name":9,"category_name":20,"show_sort_weight":21,"slug":22},4,"Exam",70,"exam",{"id":24,"doc_module":4,"doc_module_name":9,"category_name":25,"show_sort_weight":26,"slug":27},5,"Comic",60,"comic",{"id":29,"doc_module":4,"doc_module_name":9,"category_name":30,"show_sort_weight":31,"slug":32},6,"Technology",50,"technology",{"id":34,"doc_module":4,"doc_module_name":9,"category_name":35,"show_sort_weight":36,"slug":37},7,"Healthcare",40,"healthcare",{"id":39,"doc_module":4,"doc_module_name":9,"category_name":40,"show_sort_weight":41,"slug":42},8,"Research & Report",30,"research-report",{"id":44,"doc_module":4,"doc_module_name":9,"category_name":45,"show_sort_weight":46,"slug":47},9,"Religion & Spirituality",20,"religion-spirituality",{"id":46,"doc_module":4,"doc_module_name":9,"category_name":49,"show_sort_weight":46,"slug":50},"World Cup","world-cup",{"id":52,"doc_module":4,"doc_module_name":9,"category_name":53,"show_sort_weight":52,"slug":54},10,"Lifestyle","lifestyle",{"id":56,"doc_module":4,"doc_module_name":9,"category_name":57,"show_sort_weight":24,"slug":58},19,"General","general",{"code":4,"msg":60,"data":61},"ok",{"site_id":62,"language":63,"slug":64,"title":65,"keywords":66,"description":67,"schema_data":68,"social_meta":124,"head_meta":126,"extra_data":128,"updated_unix":130},105,"en","3d-printing-of-sustainable-coal-polymer-composites-study-of-processing-mechanical-performance-and-atomistic-matrix-filler-interaction","3D Printing of Sustainable Coal Polymer Composites - Study of Processing, Mechanical Performance, and Atomistic Matrix-Filler Interaction","","Bituminous coal was used as a particulate filler to produce 1.75 mm coal-plastic composite filaments for fused deposition modeling (material extrusion) 3D printing. Filaments were extruded and printed using the same processing parameters as the neat polymers, with coal loadings from 20 to 70 wt% in PLA, PETG, HDPE, and PA12. Coal improved warping of printed HDPE and enabled low-cost thermoplastic additive manufacturing. Mechanical behavior was compared with compression-molded composites: particle pull-out and particle fracture dominated failure. Tensile/flexural moduli and hardness increased with coal content, while flexural/tensile strength and impact resistance generally decreased; PA12 composites showed higher maxima than unfilled plastic. Molecular dynamics and FT spectroscopy indicated beneficial hydrogen bonding between coal and PA12, with no chemical reactions for other polymers.",{"@graph":69,"@context":123},[70,84,106],{"@type":71,"itemListElement":72},"BreadcrumbList",[73,77,79,82],{"item":74,"name":75,"@type":76,"position":8},"https://docshare.wps.com","Home","ListItem",{"item":78,"name":9,"@type":76,"position":14},"https://docshare.wps.com/document/",{"item":80,"name":40,"@type":76,"position":81},"https://docshare.wps.com/document/research-report/",3,{"item":83,"name":65,"@type":76,"position":19},"https://docshare.wps.com/document/3d-printing-of-sustainable-coal-polymer-composites-study-of-processing-mechanical-performance-and-atomistic-matrix-filler-interaction/341377/",{"url":83,"name":65,"@type":85,"image":86,"author":91,"headline":65,"publisher":94,"fileFormat":97,"inLanguage":63,"description":67,"dateModified":98,"datePublished":99,"encodingFormat":97,"isAccessibleForFree":100,"interactionStatistic":101},"DigitalDocument",{"url":87,"@type":88,"width":89,"height":90},"https://docshare.wps.com/thumbnails/3d-printing-of-sustainable-coal-polymer-composites-study-of-processing-mechanical-performance-and-atomistic-matrix-filler-interaction/341377.png","ImageObject",300,407,{"name":92,"@type":93},"Lucas Vance","Person",{"url":74,"name":95,"@type":96},"DocShare","Organization","application/pdf","2026-10-27","2026-09-22",true,{"@type":102,"interactionType":103,"userInteractionCount":105},"InteractionCounter",{"@type":104},"ViewAction",12,{"@type":107,"mainEntity":108},"FAQPage",[109,115,119],{"name":110,"@type":111,"acceptedAnswer":112},"How were coal-plastic composite filaments prepared for 3D printing?","Question",{"text":113,"@type":114},"Bituminous coal was incorporated as a particulate filler into polymer resins (PLA, PETG, HDPE, and PA12) to reach 20–70 wt% loadings, then extruded into 1.75 mm filaments. The composites were printed using processing parameters matching the corresponding neat plastics.","Answer",{"name":116,"@type":111,"acceptedAnswer":117},"What effect did coal have on warping and mechanical performance?",{"text":118,"@type":114},"Adding coal mitigated warping issues in 3D printed high-density polyethylene, supporting additive manufacturing with an inexpensive thermoplastic. Mechanical results showed moduli and hardness increased with coal content, while flexural strength, tensile strength, and impact resistance decreased for most formulations.",{"name":120,"@type":111,"acceptedAnswer":121},"What did simulations and spectroscopy reveal about coal–polymer interactions?",{"text":122,"@type":114},"Molecular dynamics simulations and Fourier-transform spectroscopy indicated beneficial hydrogen bonding interactions between coal and polyamide-12. No chemical reactions were observed for the other polymers investigated.","https://schema.org",{"og:url":83,"og:type":125,"og:title":65,"og:site_name":95,"og:description":67},"article",{"robots":127,"canonical":83},"index,follow",{"doc_id":129,"site_id":62},341377,1790168908,{"code":4,"msg":5,"data":132},{"doc_id":129,"user_id":133,"nickname":92,"user_avatar":134,"doc_module":4,"category_id":39,"category_name":40,"doc_title":65,"doc_description":67,"doc_content":135,"file_id":136,"file_url":137,"file_type":138,"file_size":139,"view_count":105,"is_deleted":4,"is_public":8,"is_downloadable":8,"audit_status":8,"page_count":140,"language":141,"language_code":63,"site_id":62,"html_lang":63,"table_of_contents":142,"faqs":143,"seo_title":144,"seo_description":67,"update_tm":145,"read_time":146,"preview_page_count":19,"preview_urls":147},549768064622,"https://ap-avatar.wpscdn.com/davatar_6f874abed73319feea01a86fa6f0fab8","[pubs.acs.org/acsapm](pubs.acs.org/acsapm)  Article   \n3D Printing of Sustainable Coal Polymer Composites: Study of Processing, Mechanical Performance, and Atomistic Matrix−Filler Interaction  \nLogan E. Veley, * Chinonso Ugwumadu, Jason P. Trembly, David A. Drabold, and Yahya Al-Majali *  \n Cite This: [https://doi.org/10.1021/acsapm.3c01784](https://doi.org/10.1021/acsapm.3c01784)  \nRead Online  \nDownloaded via STANFORD UNIV on November 2, 2023 at 13:38:43 (UTC) . See [https://pubs.acs.org/sharingguidelines](https://pubs.acs.org/sharingguidelines) for options on how to legitimately share published articles.  \nACCESS  \n Metrics & More  \n Article Recommendations  \n*sı   \nSupporting Information  \nABSTRACT: Bituminous coal was utilized as a particulate filler in polymer-based composites to fabricate standard 1.75 mm coal-plastic composite filaments for material extrusion 3D printing. The composites were formulated by incorporating Pittsburgh No. 8 coal into polylactic acid, polyethylene terephthalate glycol, high-density polyethylene, and polyamide-12 resins with loadings ranging from 20 to 70 wt %. Coalplastic composite filaments were extruded and printed by using the same processing parameters as the respective neat plastics. The introduction of coal ameliorated the warping problem of 3D printed high-density polyethylene, allowing for additive manufacturing of an inexpensive and widely available thermoplastic. The mechanical properties of the 3D printed composites were characterized and compared to those of composites fabricated using traditional compression molding. Microscopy of as-fractured samples revealed that particle pull-out and particle fracture were the predominant modes of composite failure. Tensile and flexural moduli as well as hardness had direct proportionality with increasing coal content, while flexural strength, tensile strength, and impact resistance decreased for most composite formulations. Interestingly, polyamide-based composites demonstrated greater maximum tensile and flexural strengths than unfilled plastic. Investigation of composite interfacial chemistry via molecular dynamics simulations and Fourier-transform spectroscopy revealed beneficial hydrogen bonding interactions between coal and polyamide-12, while no chemical reactions were evident for the other polymers investigated.  \nKEYWORDS: coal-plastic composite, additive manufacturing, fused deposition modeling, material extrusion, molecular dynamics simulation  \n1. INTRODUCTION  \nFused deposition modeling (FDM) is a material extrusion additive manufacturing (AM) technique where thermoplastic filaments are extruded through a heated nozzle along a desired path to build a three-dimensional object layer by layer.1 FDM provides an avenue for rapid prototyping and part production with minimal waste, but its applications have been restricted by poor mechanical performance due to limited polymer chain entanglement across print layers.1 Despite these limitations, FDM has been shown as a viable route to enter the composite tooling market which had a global value of $493 million in 2022.2,3 The development of sustainable and profitable FDM materials yields further market adoption of AM composite tooling.  \nArguably the greatest advantage of FDM is the vast array of materials available in the form of 1.75 mm filaments for printing.1 Common polymers processed via FDM include polylactic acid (PLA), polyethylene terephthalate glycol (PETG), and acrylonitrile butadiene styrene (ABS).1 Highperformance parts are frequently printed from polymers such as polyamide-12 (PA12), commonly known as nylon-12. Some commodity plastics, however, present noticeable challenges  \nwhen processed via FDM. For example, high-density polyethylene (HDPE) is rarely used in FDM applications due to poor layer adhesion, warping, and shrinkage.4,5  \nPolymer composite filaments are also processed via FDM. Particulate fillers and chopped fibers are added to the polymer filaments for aesthetic ","cbCaissSiCBz2TQf","https://ap.wps.com/l/cbCaissSiCBz2TQf","pdf",5245373,11,"English","# Abstract\n## 1. Introduction","[{\"question\":\"How were coal-plastic composite filaments prepared for 3D printing?\",\"answer\":\"Bituminous coal was incorporated as a particulate filler into polymer resins (PLA, PETG, HDPE, and PA12) to reach 20–70 wt% loadings, then extruded into 1.75 mm filaments. The composites were printed using processing parameters matching the corresponding neat plastics.\"},{\"question\":\"What effect did coal have on warping and mechanical performance?\",\"answer\":\"Adding coal mitigated warping issues in 3D printed high-density polyethylene, supporting additive manufacturing with an inexpensive thermoplastic. Mechanical results showed moduli and hardness increased with coal content, while flexural strength, tensile strength, and impact resistance decreased for most formulations.\"},{\"question\":\"What did simulations and spectroscopy reveal about coal–polymer interactions?\",\"answer\":\"Molecular dynamics simulations and Fourier-transform spectroscopy indicated beneficial hydrogen bonding interactions between coal and polyamide-12. No chemical reactions were observed for the other polymers investigated.\"}]","3D Printing of Sustainable Coal Polymer Composites - Study of Processing, Mechanical Performance, and Atomistic Matrix-Filler Interaction | PDF",1790041684,28,[148,152,156,160],{"page_no":8,"url":149,"width":150,"height":151},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-16/2b3908cb555b550f4c5f3686636c9136.webp",983,1296,{"page_no":14,"url":153,"width":154,"height":155},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-16/e21250f377a18f20539c1e334f8bb249.webp",982,1295,{"page_no":81,"url":157,"width":158,"height":159},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-16/93a1bb10fd094390db26ff38eb292b45.webp",981,1293,{"page_no":19,"url":161,"width":162,"height":163},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-16/91415c1e525886570ec13a8b7c06a9c5.webp",980,1292]